Mada za sehemu hiiConducting corrective maintenance of cutting machinesMada 7
- Performing levelling of plastic cutting block
- Re-setting the cutting pressure
- Plugging the travelling head-cutting machine into its recommended power source
- Replacing the cutting block
- Replacing electrical plugs
- Servicing and/or replacing the circuit
- Positioning the cutting machine on a balanced flat surface
A cutting block is a replaceable component in a leather cutting machine that absorbs the impact force when a die cutter strikes the leather. When the block becomes worn or damaged, it must be replaced to maintain the quality of leather cuts and to protect both the machine and the operator.
The cutting block serves two main functions:
- Absorbs impact – When the cutting press descends, the block cushions the die's strike and prevents damage to the machine bed and to the sharp edge of the die
- Ensures clean cuts – A worn block produces uneven or jagged edges on leather pieces
Before starting any replacement work, always observe these safety measures:
- Wear industrial gloves to protect hands from sharp edges
- Wear a dust coat to protect clothing
- Keep the first aid kit nearby in case of minor injuries
- Ensure the machine is switched off and disconnected from power, and wait until the motor has stopped completely
- Never put your hands under the cutting head, and never let another person touch the controls while you work on the block
- Wear closed shoes and tie back long hair and loose sleeves
- Use load carrier trolleys to safely transport heavy blocks, and lift a block with a partner, bending your knees and keeping your back straight
You will need the following tools:
- Socket spanners (various sizes)
- Set of screwdrivers (flat-head and Phillips)
- Gloves and dust coat
- First aid kit
- Load carrier trolleys
Step 1: Prepare the Machine
- Switch off the leather cutting machine
- Disconnect the power supply cable
- Remove all cutting dies and leather from the block
- Swing the cutting head aside, or raise it fully, so that it is clear of the block
- Position a load carrier trolley beside the machine for the old block
Step 2: Remove the Old Cutting Block
- Locate the cutting block on the machine bed or holder
- Use appropriate screwdrivers to loosen and remove any securing screws or clamps
- Use socket spanners to remove any nuts or bolts holding the block in place
- Carefully lift the old block with a partner, or slide it straight onto the trolley if it is heavy
- Place the old block on the load carrier trolley for safe disposal or recycling
Step 3: Inspect the Mounting Area
Before installing the new block, check:
- The mounting surface is clean and free from debris
- No screws, bolts, or debris are stuck in the holder
- The mounting holes or slots are not damaged
Step 4: Install the New Cutting Block
- Check that the new block is the same size and thickness as the old one and that its faces are flat, then position it in its recommended position on the machine bed
- Align the mounting holes or slots with the corresponding holes on the machine
- Insert and hand-tighten the screws or bolts
- Use socket spanners to securely tighten all fasteners in a diagonal pattern to ensure even seating
- Double-check that the block is firmly held and does not move
Step 5: Adjust the Cutting Head and Test
- With the power still off, place a cutting die on a scrap of leather on the new block and bring the cutting head over it. Adjust the height of the head until it is a little above the top of the die, about 10 to 20 mm or as the machine's manual states. Reset the height whenever you change to a taller or shorter die
- Clear all tools from the machine, reconnect the power and switch on. Start with a low pressure setting and run a test cut on the scrap, pressing the control buttons with both hands
- Check that the cut edge is clean and even
- If the die has not cut through, raise the pressure a little at a time. If the cut is still uneven, switch off, disconnect the power and check that the block is seated flat and held firmly
- Always replace a worn block promptly to avoid poor-quality leather products
- The block must be positioned exactly as recommended by the machine manufacturer
- Always use the correct tools to avoid damaging the block or machine
- Safety equipment must be worn at all times during replacement
- A new block is thicker than a worn one, so the height of the cutting head must be reset after every replacement
- Move the die to a different place for each cut, and turn the block round regularly, so that the new block wears evenly
- Switch off and disconnect the machine again before cleaning
- Brush leather scraps and dust from the block, the bed and the floor around the machine, and wipe away any oil
- Wipe the socket spanners and screwdrivers and return them to the tool board or toolbox
- Store the cutting dies on their rack with the cutting edges protected
- Take the old block away on the trolley. A block that is worn on one face only can be stored lying flat, to be resurfaced or used on its other face; a cracked block goes to the place set aside for waste plastic
Working in groups of 3–4 students:
- Discuss and list the steps needed to replace a cutting block
- Each group member takes a role: one removes the block, one handles tools, one inspects the area, and one tests the installation
- Replace the cutting block on the available leather cutting machine
- Record any observations about the condition of the removed block
In a small-scale shoe-making workshop in Arusha, a cobbler uses a leather cutting machine daily to cut sole pieces from rubber sheets. When the cutting block becomes worn after months of use, the cobbler must replace it to maintain clean cuts and avoid wasting expensive sole material. Understanding how to safely replace the cutting block helps the cobbler keep production running smoothly without costly machine repairs or spoiled materials.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Observe the safety precautions of the machine
- Adjust height of the Cutting head according to the sizes of the cutting dies
- Replace the cutting block
- Observe safety
- Clean tools, equipment, and machine
- Store tools and equipment
Tathmini ya matokeo
The cutting block is replaced in its recommended position properly
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to replace the cutting block in its recommended position
Principles: The student should explain the principles of replacing the cutting block
Theories: The student should explain: Safety precautions for replacing the cutting block
Circumstantial knowledge:
Detailed knowledge of:
- Safe handling of workshop cutting block
Swali
What happens to the leather pieces when the cutting block of a cutting machine is badly worn?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado