Mada za sehemu hiiConducting corrective maintenance of cutting machinesMada 7
- Performing levelling of plastic cutting block
- Re-setting the cutting pressure
- Plugging the travelling head-cutting machine into its recommended power source
- Replacing the cutting block
- Replacing electrical plugs
- Servicing and/or replacing the circuit
- Positioning the cutting machine on a balanced flat surface
A plastic cutting block is the thick board of tough plastic, such as nylon or polypropylene, that lies on the bed of a leather cutting machine (a clicking press). The leather is laid on the block, a cutting die (a shaped steel knife) is placed on the leather, and the cutting head presses the die through the leather and slightly into the block. Levelling means making sure that the surface of the block is flat and even, and setting the machine so that the head meets the die squarely with just enough pressure to cut.
- It supports the leather and the die during cutting
- It protects the sharp edge of the die, because plastic is softer than steel
- It protects the bed of the machine
- It lets the die pass right through the leather, so the cut is clean
Every cut leaves a small mark in the block. If the die is always placed in the same spot, a hollow forms there. On an uneven block the die does not cut through everywhere, so pieces come out with ragged edges or hang on by threads. The operator is then tempted to raise the pressure, which cuts deeper grooves, bends or breaks dies and wastes leather. Four principles keep a block level:
- Spread the wear: move the die to a different place for each cut, and turn the block round or over regularly
- Keep the block seated flat on a clean bed
- Set the cutting head at the right height above the die
- Use the lowest hydraulic pressure that cuts cleanly
- Fix spanners, ring spanners and socket spanners, for the clamps or stop bolts that hold the block
- Screwdrivers, for guards and covers
- Hammer, used with a block of wood to tap the cutting block into position
- A straight edge or long steel rule, to check flatness
- Dust coat and industrial gloves
- First aid kit, kept where everyone can reach it
- Load carrier trolley, for moving the heavy block
Step 1: Make the machine safe
- Switch off the machine and isolate it at the wall switch. Wait until the motor has stopped.
- Button your dust coat, tie back long hair and wear gloves for handling the block and the dies.
- Remove all dies and leather, and swing the cutting head aside so that nothing hangs over your hands.
Step 2: Clean and inspect the block
- Brush off leather scraps and dust.
- Lay the straight edge across the block from left to right, from front to back and from corner to corner. Light showing under the straight edge means a hollow.
- Mark hollows and raised ridges with chalk.
Step 3: Level the surface
- If clamps or stop bolts hold the block, loosen them with the correct spanner. With a partner, turn the block round so that a fresh area lies under the head, or turn it over to use the other face.
- Clean the bed before putting the block back. A scrap of leather trapped under the block tilts it.
- Seat the block flat, tap it into position and tighten the clamps evenly.
- A block with deep hollows or grooves on both faces cannot be levelled by hand. It is sent to be planed flat on a block-planing machine, or it is replaced. Do not file or sand it down yourself, because this leaves the surface more uneven.
Step 4: Adjust the height of the cutting head
- With the power still off, lay a piece of scrap leather on the block and place a die on it, cutting edge down.
- Swing the head over the die and turn the height adjustment until the head is a little above the top of the die: about 10 to 20 mm, or as the machine's manual states.
- If the head is too high, the stroke is long and the cut is weak. If it is too low, the die cannot be slid under safely.
- Reset the height every time you change to a taller or shorter die.
Step 5: Regulate the hydraulic pressure
- Set the pressure control low, then reconnect the power and switch on.
- Stand squarely and press the two control buttons with both hands. The two-hand control keeps your hands out from under the head.
- Make a test cut on scrap leather. If the die has not cut through everywhere, raise the pressure a little and test again.
- Stop when the die cuts cleanly and leaves only a faint mark on the block.
- Test in several places. If the die cuts cleanly in one place and not in another at the same setting, the block is still not level, so switch off and go back to Step 3.
Step 6: Place the cutting dies correctly
- Place the die flat on the leather, cutting edge down, and fully under the head, never half off the edge of the block.
- Move the die to a different part of the block for each cut.
- Never stack one die on another.
- Take your hands off the die before the head comes over it.
In a school workshop in Mtwara, a student notices that sandal soles cut near the middle of the block hang on by threads, while those cut near the edges are clean. A straight edge shows a hollow about 2 mm deep in the middle. With the power isolated, she and a partner loosen the clamps, turn the block over to its unused face, clean the bed and tighten the clamps again. She resets the head height above the die, starts with low pressure and raises it step by step until a scrap is cut cleanly. The soles now come out clean all over the block, and from then on she moves the die around instead of always cutting in the middle.
- Switch off and isolate the machine before cleaning.
- Brush the block and the bed, sweep up scraps and put them in the waste bin. Report any oil leaking from the machine.
- Wipe the spanners and screwdrivers and return them to the tool board or toolbox.
- Store the dies on their rack with the cutting edges protected.
- Move a spare block on the trolley and store it lying flat, away from sun and heat, so that it does not warp.
- Only one person operates the machine. Never reach under the head, and never tape down or jam a control button.
- Isolate the power before touching the block, the clamps or anything under the head.
- The block is heavy: lift it with a partner, bending your knees, or use the trolley.
- Report strange noises, oil leaks and damaged guards at once. A crushed finger or a deep cut is an emergency: stop the machine, call the teacher and use the first aid kit while help is on the way.
A shoemaker in Arusha who cuts uppers and soles on a clicking press checks the cutting block with a straight edge every week, turns it regularly and keeps the pressure as low as the job allows. The dies stay sharp, the pieces come out clean, less leather is spoiled, and each hide yields more pairs of shoes to sell.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to correctly:
- Observe safety precautions of the machine
- Adjust the height of the cutting head to get positions of the cutting block
- Regulate hydraulic pressure
- Place the cutting dies on the leather material
- Observe safety
- Clean tools, equipment, and machines
- Store tools and equipment
Tathmini ya matokeo
Plastic cutting blocks are levelled according to the required specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to correctly: Perform levelling of the plastic cutting block of the cutting machine
Principles: The student should clearly explain the principles of:
- Levelling of the plastic cutting block
Theories: The student should explain clearly:
- Uses of plastic cutting block
Circumstantial knowledge:
Detailed knowledge of:
- Safe handling of workshop facilities
Swali
Why is the cutting block of a clicking press made of tough plastic and not of steel?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado