Mada za sehemu hiiProducing sawn timberMada 5
- Determining sawing pattern
- Operating sawmill
- Re-sawing cants and slabs
- Edging side boards
- Trimming sawn boards
Determining Sawing Patterns
Sawing patterns are the different ways a log is cut to produce sawn timber. The pattern chosen determines the grain appearance, board width, timber stability, and overall yield. The sawmill operator must select the appropriate pattern based on the log quality, intended use of the timber, available equipment, and customer requirements.
There are four main sawing patterns used in Tanzanian sawmills:
1. Through-and-Through (Live) Sawing
This is the simplest method where a series of parallel cuts are made through the log without turning it. The log stays in one position while the saw makes successive cuts from one end to the other.
Advantages
- Highest timber recovery rate (70-90%)
- Simple operation requiring less skill
- Produces the widest boards possible
- Faster drying time for the timber
- Low milling costs
Disadvantages
- Boards are prone to cupping during drying
- Not suitable for structural timber
- Wane (bark edges) appears on two sides of boards
- Less flexible for different log sizes and qualities
2. Quarter Sawing
In quarter sawing, the log is first cut into four equal quarters. Then, planks are cut from each quarter at angles between 45° and 90° to the growth rings. This produces radially sawn timber with the cuts running parallel to the wood rays.
Advantages
- Excellent dimensional stability
- Minimal warping, twisting, or cupping
- Less surface checking during drying
- Smoother surface due to straight grains
- Attractive grain pattern for furniture making
Disadvantages
- Lower timber yield (produces narrower boards)
- More waste compared to through-and-through
- Requires more skill and labour
- Higher cost per cubic metre
- Slower production rate
3. Grade (Round-the-Log) Sawing
Grade sawing produces timber according to quality grades. The operator cuts one face of the log, evaluates the wood quality exposed, then turns the log 90° and cuts the next face. This process continues until all four faces are cut. The central portion (cant) is then resawn.
Advantages
- Flexible method that maximises high-grade timber
- Can extract best quality wood from each log face
- Suitable for large tropical logs
- Better than quarter sawing for rapid drying
- Handles logs with defective interiors well
Disadvantages
- Lower production rates due to frequent turning
- Higher production costs
- Requires highly skilled sawyers
- More waste when processing low-quality logs
- Complex log handling requirements
4. Cant Sawing
Cant sawing makes the first cut across the top of the log to produce a squared piece called a cant. The cant is then rotated 90° and cut by a second saw into sideboards and timber. This method is commonly used for medium and low-quality logs.
Advantages
- Maximises cubic metre production per day
- Cost-effective for low-grade logs
- Produces boards with good width
- Removes juvenile wood near the pith
- Simple cutting technique
Disadvantages
- Higher waste compared to other methods
- Boards tend to cup, twist, and bow during drying
- May produce timber with excessive sapwood
- Lower-grade final products
- Longer processing time
The sawmill operator considers several factors when selecting a sawing pattern:
- Log diameter and length: Large logs may allow for quarter or grade sawing, while small logs suit through-and-through
- Log quality and defects: Grade sawing works best for logs with variable quality
- Intended use: Quarter sawn for furniture, through-and-through for construction
- Available equipment: Some machines only support certain patterns
- Required timber dimensions: Width and thickness requirements
- Market demand: Customer specifications for grain pattern
- Production targets: High-volume needs favour cant or through-and-through
A sawmill in Morogoro receives a batch of 50 Pine logs with an average diameter of 40 cm and length of 3.6 m. The logs are straight with few defects. The market locally demands timber for general construction framing.
Analysis
- Log quality: Good (straight, few defects)
- Diameter: Medium (40 cm)
- End use: Construction framing
Recommended pattern: Through-and-through sawing
Reasoning: For straight, good-quality logs of medium diameter destined for construction, through-and-through provides the highest recovery (70-90%), lowest cost, and fastest production. Construction timber does not require the premium stability of quarter-sawn wood.
If the same logs were destined for furniture making in Dar es Salaam, quarter sawing would be preferred despite lower yield, because furniture requires superior dimensional stability and attractive grain patterns that command higher prices.
In Tanzania, small-scale sawmill operators in districts like Kilombero or Shinyanga regularly decide which sawing pattern to use based on the logs they purchase. For example, a local sawmill owner buying teak logs from a forest near Mikumi will choose quarter sawing for logs destined for furniture workshops in Dar es Salaam because the higher stability and attractive grain command premium prices (around TSh 500,000-800,000 per cubic metre for quarter-sawn teak versus TSh 250,000-400,000 for plain-sawn). Understanding which pattern maximises value from each log helps the operator make profit or loss on every load of timber processed.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
Group discussion: pattern
- Determine sawing
- Adhere to safety principles
- Clean tools
- Store tools
Tathmini ya matokeo
Sawing pattern - Identify sawn pattern correctly determined.
Tathmini ya maarifa
Sawing knowledge of:
Method used: The students should explain how to:
- Identify sawn pattern
- Determine sawing pattern
- Adhere to safety principles
Principles: The student should explain principles of sawing patterns.
Theories: The explain importance
- Through
- Quarter sawing
- Grade sawing
Circumstantial knowledge:
Detailed knowledge about: Safety precautions involved in sawing logs
Swali
Which of the following is NOT a main type of sawing pattern used in Tanzanian sawmills?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado