Mada za sehemu hiiDesigning and making liquid coolersMada 5
A juice cooler body is the outer shell or casing that holds all the components of a juice cooling system. It protects the internal parts (such as the refrigeration cycle components) and provides insulation to keep the juice cold. In this learning activity, you will design and fabricate the body of a simple juice cooler using sheet metal and appropriate joining techniques.
The following materials are commonly used:
- Galvanized iron (GI) sheet — durable and resistant to corrosion
- Aluminum sheet — lightweight and easy to shape
- Insulation materials — such as polystyrene or polyurethane foam to reduce heat transfer
- Rivets — for joining metal sheets together
- Paint — for surface protection and finishing
Before starting the fabrication, ensure the following tools are available:
- Measuring tools: tape measure, steel rule, vernier caliper
- Marking tools: scriber, punch, marking hammer
- Cutting tools: snips (hand shears), shearing machine
- Bending tools: bending machine, folder
- Joining tools: pop rivet gun, soldering gun, resistance welding machine
- Finishing tools: spray painting compressor, file, sandpaper
- Safety gear: gloves, safety goggles, welding helmet, ear protection
Step 1: Planning and Design
- Determine the dimensions of the cooler based on the juice container size (for example, a 2-litre plastic bottle or a 5-litre jerry can)
- Draw a simple sketch showing the front, top, and side views with all measurements
- Calculate the total surface area of sheet metal needed
Step 2: Measuring and Marking
- Use a tape measure to measure and mark the required dimensions on the sheet metal
- Mark cutting lines, bending lines, and hole positions clearly using a scriber
- Double-check all measurements before cutting to avoid waste
Step 3: Cutting the Sheet Metal
- Use snips or the shearing machine to cut the metal according to the marked lines
- Ensure cuts are straight and clean
- Deburr edges using a file to remove sharp spots
Step 4: Bending and Forming
- Use the bending machine to form the sides, top, and bottom panels
- Follow the bending lines marked earlier
- Ensure consistent bend angles (typically 90 degrees for box-shaped coolers)
Step 5: Assembling the Body
- Position the cut and bent panels together to form the box shape
- Align all edges properly
- Use a pop rivet gun to join panels together with rivets at regular intervals (every 50–80 mm)
- Alternatively, use spot welding for permanent joints
Step 6: Installing Insulation
- Cut insulation material to fit inside the cooler body
- Place the insulation on the inner surfaces of the body
- Secure with adhesive or mechanical fasteners
Step 7: Finishing
- File and sand all edges to remove sharp corners
- Clean the surface to remove dirt and grease
- Apply primer and then spray paint for rust protection and good appearance
Step 8: Quality Check
- Check for gaps or leaks in the joints
- Verify that doors or lids close properly
- Ensure all dimensions match the original design
A student wants to make a juice cooler body to fit a 2-litre juice bottle. The cooler is designed as a rectangular box with the following internal dimensions:
- Length = 250 mm
- Width = 250 mm
- Height = 400 mm
Calculate the sheet metal area needed for the four sides (excluding top and bottom):
Area of two longer sides = 2 × (length × height) = 2 × (250 mm × 400 mm) = 2 × 100,000 mm² = 200,000 mm²
Area of two shorter sides = 2 × (width × height) = 2 × (250 mm × 400 mm) = 2 × 100,000 mm² = 200,000 mm²
Total side area = 200,000 + 200,000 = 400,000 mm²
Convert to square metres: 400,000 mm² ÷ 1,000,000 = 0.4 m²
Therefore, the student needs approximately 0.4 m² of sheet metal for the four sides alone.
- Always wear safety goggles when cutting or drilling metal
- Use gloves to protect hands from sharp edges
- Ensure proper ventilation when spray painting or welding
- Keep the work area clean and free of flammable materials
- Always disconnect power when using electrical tools
In Tanzania, juice coolers are commonly used by small-scale juice vendors in markets such as Mwanza, Arusha, and Dodoma to keep freshly squeezed mango, orange, or sugarcane juice cold throughout the day. A vendor can use a self-made juice cooler body to preserve drinks without relying on expensive imported refrigeration units, reducing costs and increasing profit margins. This practical skill also enables technicians to repair or fabricate cooler bodies for local restaurants and grocery shops, supporting small businesses in the community.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Select materials, tools and equipment
- Draw detailed drawing and assembly drawings
- Draw electrical wiring circuits
- Prepare the system main body structures of the liquid coolers
- Mount the refrigerating compound in the case
- Make a refrigerating cabinet body and cooling coil
- Perform wiring circuits for both heating and cooling
- Perform spray painting
- Charge with refrigerant R134a
- Apply safety gears
- Clean workplace, tools and equipment
- Store tools and equipment
- Commission the system performance
Tathmini ya matokeo
Designed and made liquid coolers conform to the technical specifications and aesthetic appearance
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Make different kind of coolers
- Apply safety measures
Principles: The student should explain the principles of: (c) Heat transfer and exchange (d) Design characteristics/para meters
Theories: The student should explain:
- The functional of components
- Refrigeration cycle
- Heat load estimation/calculations
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling of tools, equipment and machines
- Environmental regulations
Swali
Which of the following materials is commonly used for making the outer shell of a juice cooler body?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado