Mada za sehemu hiiServicing compressor above 60 kWMada 7
Lubricating Bearings in Refrigeration Compressors
Bearing lubrication is a critical maintenance procedure in refrigeration and air conditioning systems, particularly for compressors rated above 60 kW. Proper lubrication reduces friction between moving parts, dissipates heat, prevents wear, and extends the service life of the compressor. This study note covers the purpose, procedure, and safety requirements for lubricating bearings in industrial refrigeration systems.
Bearings in refrigeration compressors support rotating shafts and allow smooth movement with minimal friction. Without proper lubrication:
- Friction increases between the bearing surfaces and the shaft
- Heat builds up due to friction, which can damage bearing materials
- Wear accelerates, leading to premature bearing failure
- Noise and vibration develop, reducing system efficiency
- Energy consumption rises as the compressor works harder
Lubricating oil or grease creates a protective film between bearing surfaces, keeping the compressor running smoothly and efficiently.
1. Ball Bearings
- Use rolling elements (balls) to reduce friction
- Commonly found in small to medium-sized compressors
- Require regular lubrication with appropriate grease or oil
2. Roller Bearings
- Use cylindrical rollers for heavier loads
- Often used in large industrial compressors above 60 kW
- Need oil bath lubrication or grease filling
3. Sleeve Bearings
- Also called plain bearings
- Rely entirely on a film of oil for operation
- Common in older or specific industrial compressor designs
Follow these systematic steps when lubricating bearings in a refrigeration compressor:
Step 1: Prepare the Work Area
- Clear the area around the compressor
- Ensure adequate lighting using inspection lamps or flashlights
- Place a pail or container to catch any oil or grease that drips
- Verify all required tools and equipment are available
Step 2: Observe Safety Precautions
- Wear working hand gloves to protect hands from hot surfaces and chemicals
- Put on a dust mask when cleaning old grease or debris
- Ensure the compressor is switched off and disconnected from power
- Allow the compressor to cool to a safe temperature before beginning
Step 3: Access the Bearing
- Use appropriate lifting tackles if the compressor housing needs to be opened
- Follow manufacturer instructions for removing access panels
- Take care not to damage refrigerant lines or electrical connections
Step 4: Clean the Bearing
- Use a wire brush or revolving wire brush to remove old grease and debris
- Apply compressed air using the compressed air hose to blow out dust and particles
- Ensure the bearing housing is clean before applying new lubricant
Step 5: Inspect the Bearing
- Check for visible signs of wear, scoring, or damage
- Look for discoloration that may indicate overheating
- Use a refrigerant leak detector to check for refrigerant leaks around the bearing area
- If damage is detected, replace the bearing rather than relubricating
Step 6: Apply the Lubricant
- Select the correct lubricant as specified by the compressor manufacturer
- Use a grease gun for grease-lubricated bearings
- Apply oil bath lubrication for sleeve bearings using the appropriate oil grade
- Add lubricant until the bearing housing is filled to the recommended level
Step 7: Reassemble and Test
- Refit all covers and panels removed during access
- Secure all fasteners properly
- Reconnect power and start the compressor
- Listen for unusual noise and check for excessive vibration
- Monitor operating temperatures to ensure proper lubrication
| Tool | Purpose |
|---|---|
| Grease gun | Inject grease into bearing housing |
| Wire brush / Revolving wire brush | Remove old grease and debris |
| Compressed air hose | Blow out dust and particles |
| Lifting tackles | Safely access compressor components |
| Inspection lamp / Flash light | Provide adequate lighting |
| Dust mask | Protect respiratory system |
| Working hand gloves | Hand protection |
| Refrigerant leak detector | Check for leaks |
| Pail or containers | Collect oil/grease drips |
- Over-lubricating — excess grease can cause overheating and seal damage
- Under-lubricating — insufficient lubrication leads to rapid wear
- Using wrong lubricant — always use manufacturer-recommended oil or grease grade
- Skipping cleaning — old lubricant contaminates new lubricant
- Lubricating hot bearings — always allow cooling before applying lubricant
A service technician is performing routine maintenance on a 75 kW industrial air conditioning compressor. During inspection, the technician finds the bearing housing is nearly empty of grease and the bearing shows early signs of dryness.
Procedure followed:
- Switched off the compressor and locked out the electrical supply
- Waited 30 minutes for the compressor to cool
- Opened the bearing access panel using hand tools from the electro mechanical toolbox
- Cleaned the old grease from the bearing using a wire brush
- Blew out dust particles with compressed air
- Applied fresh grease using a grease gun until the housing was properly filled
- Reassembled the panel and restarted the compressor
The compressor returned to normal operation with reduced noise and vibration, demonstrating the importance of regular bearing lubrication.
In Tanzania, many commercial buildings in Dar es Salaam and other cities use large air conditioning systems in hotels, hospitals, and offices. These systems contain compressors above 60 kW that require regular bearing maintenance. A technician working at a local hotel's central air conditioning plant would routinely lubricate bearings during scheduled maintenance to prevent sudden breakdowns, ensuring comfort for guests while avoiding costly emergency repairs that could interrupt business operations.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment for a task
- Performing diagnostic troubleshooting
- Performing bearing greasing
- Performing pump down
- Replace air filters
- Repair compressors
- Detect leaks
- Performing sheet metal works
- Inspect electrical components
- Carry out plumbing works
- Check/refill oil level
- Store tools and equipment
- Clean equipment and workplace
Tathmini ya matokeo
A record of service works carried out conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Assemble and disassemble according to procedures
- Apply different leakage detection methods
- Performing diagnostic trouble shooting
Principles: The student should explain the principles of:
- Heat transfer in a heat exchanger
- Compression refrigeration cycle
- Primary and secondary refrigerants
Theories: The student should explain:
- Pressure temperature charts for different refrigerants
- Super heating as it refers to refrigeration
- Application of oil and greasing lubricants
Detailed knowledge about:
- Safe handling of working tools and equipment
- Electric circuitry
- Pressure and temperature quantities with reference to refrigeration
- Safe handling of refrigerants during charging, discharging and storage
- Environmental regulations on green gases
Swali
What is the PRIMARY purpose of lubricating bearings in refrigeration compressors?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado