Mada za sehemu hiiConstructing inductive circuitsMada 4
A series circuit is a circuit where all components are connected one after another in a single path, so the same electric current flows through each component. If one component breaks or is disconnected, the entire circuit stops working. In refrigeration and air conditioning, series circuits are used to connect components like switches, thermostats, motors, and compressors.
A simple series circuit for learning purposes includes:
- Power source (battery) — provides the electric energy
- Load (resistor or inductor) — converts electrical energy to other forms (light, heat, motion)
- Switch — controls the circuit by opening or closing the path
- Connecting wires — carry current from one component to another
Each component must be properly connected for the circuit to work.
1. Plan the Circuit
Before connecting, draw a simple circuit diagram on paper. Place the battery, switch, load (such as a resistor or inductor), and wires in a single loop.
2. Gather Materials and Safety Gear
Put on your safety equipment before starting:
- Overalls and safety boots
- Safety goggles
- Use insulated tools
3. Prepare the Wires
Using an electrician knife, strip about 1 cm of insulation from both ends of each wire. Use combination pliers to bend the exposed ends into small loops for easy connection.
4. Connect the Components
Connect the components on the proto board following your diagram:
- Connect one terminal of the battery to one terminal of the switch
- Connect the other terminal of the switch to one end of the load (resistor or inductor)
- Connect the other end of the load back to the other terminal of the battery
This creates a single continuous path.
5. Test the Circuit
Close the switch and observe. Use a multimeter to measure:
- Voltage across each component
- Current at any point in the circuit (it should be the same everywhere in a series circuit)
If the circuit does not work, check all connections are tight and the switch is closed.
- Same current flows through all components: The current has only one path to take.
- Total resistance equals the sum of individual resistances: Rtotal=R1+R2+R3
- Total voltage equals the sum of voltage drops: Vtotal=V1+V2+V3
- If one component fails, the whole circuit stops: This is important for troubleshooting.
A simple series circuit has a 12V battery, a switch, and an inductor (like a small motor) with resistance of 4 Ω.
Calculate the current flowing through the circuit when the switch is closed.
Using Ohm's Law: I=RV=4Ω12V=3A
The current of 3 amperes flows through every component because they are connected in series.
In refrigeration systems, series circuits are used to connect:
- The thermostat switch
- The compressor motor
- The condenser fan motor
- Overload protection devices
When the thermostat calls for cooling, all these components must work together in the series path.
If the circuit does not work:
- Verify the switch is closed
- Check all wire connections are secure
- Test each component individually with a multimeter
- Look for broken wires or loose terminals
In Tanzania, refrigeration technicians in Dar es Salaam and other regions use series circuit knowledge when installing or repairing split air conditioners. When the indoor unit's thermostat calls for cooling, the circuit must carry current through the compressor, fan motor, and capacitor — all connected in series. Understanding series circuits helps technicians diagnose why an air conditioner might not start, such as a faulty thermostat or a damaged compressor motor winding.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret the given circuit diagram of the inductive circuit
- Select equipment, tools and material required
- Prepare inductors and wires for termination
- Build an inductive circuit in series
- Solder the built circuits
- Test the built inductive circuits
- Clean work area, tools and equipment
- Store tools, equipment and excess materials
Tathmini ya matokeo
The inductive circuits constructed as per technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Construct inductive circuits
- Identify an inductor
- Calculate the value of inductance
Principles: The student should explain the principles of:
- Constructing inductive circuits
- Carrying out measurement of voltage across an inductive circuit
Theories: The student should explain:
- The series inductive circuit and its behaviour
- The application of the various types of inductive circuit
Detailed knowledge about:
- Safety precaution in inductive circuits Safe handling of working tools, equipment and the inductors
Swali
What happens to the entire series circuit if one component fails or is disconnected?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado