Mada za sehemu hiiConstructing inductive circuitsMada 4
- Building single inductor circuits
- Building series circuits
- Building parallel circuits
- Building combined series parallel circuits
A parallel circuit is an electrical circuit where components are connected across the same two points, providing multiple paths for current to flow. In a parallel circuit, each component receives the full voltage from the power source, and the total current splits between the different branches.
When building a parallel circuit, you will work with the following components:
- Power source (battery) – provides electrical energy
- Load components (such as resistors or inductor coils) – devices that use electrical energy
- Connecting wires – conduct electricity between components
- Switch – controls the circuit by opening or closing the flow
- Multimeter – measures voltage, current, and resistance
Always wear safety gear (overalls, safety goggles, and work boots) when working with electrical circuits.
Step 1: Plan the Circuit Layout
Before connecting anything, draw a simple diagram on paper. In a parallel circuit, each component connects directly across the power source. For example, if you have two resistors (R1 and R2), both should have one end connected to the positive terminal and the other end connected to the negative terminal of the battery.
Step 2: Prepare the Proto Board
Place the proto board on your work bench. Use the electrician knife to strip the ends of your connecting wires if needed. Use combination pliers and long nose pliers to handle small components carefully.
Step 3: Connect the First Branch
Connect one end of your first component (such as a resistor or inductor) to the positive terminal of the battery using a wire. Connect the other end of this component to the negative terminal of the battery with another wire. This creates your first parallel branch.
Step 4: Add the Second Branch
Take your second component and connect one end to the same positive point where the first component connects. Connect the other end to the same negative point. You have now built a parallel circuit with two branches.
Step 5: Insert the Switch
Connect the switch in series with the power source (before the point where branches split). This allows you to control the entire parallel circuit with one switch.
Step 6: Test and Measure
Use the multimeter to verify your circuit is working correctly. Measure the voltage across each branch—you should find the same voltage across both branches in a parallel circuit.
-
Same voltage: Each branch in a parallel circuit receives the full source voltage. If your battery provides 12V, each branch will have 12V across it.
-
Current division: The total current from the source splits between the branches. Each branch current depends on the resistance of that branch.
-
Total resistance: The total resistance in a parallel circuit is less than the smallest individual resistance. For two equal resistors in parallel, the total resistance is half of one resistor.
Rtotal=R1+R2R1×R2
- Independent branches: If one branch is disconnected or fails, the other branches continue to operate. This is why household wiring uses parallel circuits.
A student builds a parallel circuit with a 12V battery and two inductor coils. Coil 1 has a resistance of 6Ω, and Coil 2 has a resistance of 6Ω.
Finding the total resistance:
Rtotal=6+66×6=1236=3Ω
Finding the total current from the battery:
Itotal=RtotalV=3Ω12V=4A
The current divides equally between the two branches, so each branch carries 2A. Each coil still receives the full 12V across it.
- Household wiring: All appliances in a home are connected in parallel so each gets full voltage and can operate independently
- Vehicle wiring: Headlights, taillights, and other systems use parallel circuits
- Refrigeration systems: Electrical components in refrigerators and air conditioners are often wired in parallel for reliable operation
In Tanzania, parallel circuits are used in most electrical installations in homes and businesses. For example, when an electrician wires a small shop in Dar es Salaam, they connect all the lights and power sockets in parallel. This ensures that if one light bulb burns out, the other lights and sockets continue working normally, and each appliance receives the full 220V from the TANESCO supply needed to operate properly.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret the given circuit diagram of the inductive circuit
- Select equipment, tools and material required
- Prepare inductors and wires for termination
- Build a parallel inductive circuit
- Solder the built circuits
- Test the built inductive circuits
- Clean work area, tools and equipment
- Store tools, equipment and excess materials
Tathmini ya matokeo
The inductive circuits constructed as per technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Construct inductive circuits
- Identify an inductor
- Calculate the value of inductance
Principles: The student should explain the principles of:
- Constructing inductive circuits
- Carrying out measurement of voltage across an inductive circuit
Theories: The student should explain:
- The parallel inductive circuit and its behaviour
- The application of the various types of inductive circuit
Detailed knowledge about:
- Safety precaution in inductive circuits Safe handling of working tools, equipment and the inductors
Swali
What is a parallel circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado