Mada za sehemu hiiConstructing inductive circuitsMada 4
- Building single inductor circuits
- Building series circuits
- Building parallel circuits
- Building combined series parallel circuits
Combined Series-Parallel Circuits
A combined series-parallel circuit is a circuit that has some components connected in series and others connected in parallel within the same circuit. This type of circuit is very common in refrigeration and air conditioning equipment, particularly in the motor winding arrangements of compressors and fans.
In this topic, you will learn how to build and analyze such circuits using inductors (coils), which are essential components in refrigeration systems.
Series Connection
Components are connected end-to-end, forming a single path for current flow:
- Current is the same through all components
- Total resistance = sum of individual resistances
- If one component fails, the entire circuit breaks
Parallel Connection
Components are connected across the same two points, creating multiple paths for current flow:
- Voltage is the same across all components
- Total resistance is less than the smallest individual resistance
- If one component fails, other paths continue to work
Combined Series-Parallel Connection
In a combined circuit, some components are in series and others are in parallel. For example, two inductors might be connected in parallel, and this combination is then connected in series with a switch and power source.
Components Required
- Battery (power source)
- Two or more inductors (coils)
- Wires with connectors
- Switch
- Multeter (for testing)
Step-by-Step Procedure
-
Plan your circuit layout – Identify which inductors will be in parallel and which will be in series with the rest of the circuit.
-
Connect the parallel section first – Connect the inductors that should be in parallel between the same two points.
-
Add the series components – Connect the switch and wires in series with the parallel combination.
-
Connect to power – Attach the battery last, ensuring correct polarity.
-
Test the circuit – Use a multimeter to verify connections and measure current flow.
Problem: Build a circuit where two inductors (L₁ = 10Ω and L₂ = 20Ω) are connected in parallel, and this parallel combination is connected in series with a switch and a 12V battery.
Solution:
Step 1: Draw the circuit diagram
┌──────L₁──────┐
│ │
─────┤ ├─────┐
+ │ (parallel) │ │
─────┤ ├─────┤
│ │ │
└──────L₂──────┘ │
│
SWITCH ────────┤
│
(battery) ─────┴────
-
Step 2: Calculate equivalent resistance of parallel section
For parallel resistors:
Req1=R11+R21=101+201=202+201=203
Req=320≈6.67Ω
Step 3: Total resistance in series circuit
Rtotal=Req=6.67Ω
Step 4: Calculate total current using Ohm's Law
I=RV=6.67Ω12V≈1.8A
Step 5: Build the circuit
- Connect L₁ and L₂ in parallel on the proto board
- Connect the switch in series with the parallel combination
- Connect the 12V battery last
- Close the switch and verify with multimeter
- Always identify which components are in series and which are in parallel before building
- Use the multimeter to check connections before applying power
- Ensure all connections are secure to avoid open circuits
- Follow safety procedures: wear safety goggles, use proper tools
In Tanzania, refrigerator and air conditioning repair technicians regularly encounter series-parallel circuits when working on compressor motor windings. For example, when troubleshooting a faulty domestic refrigerator in Dar es Salaam, a technician may find that the start winding and run winding of the compressor motor are connected in series, and this series combination is in parallel with other components on the control board. Understanding how these circuits work helps the technician diagnose whether the problem is a broken winding (open circuit) or a short circuit, enabling proper repair and reducing the cost of unnecessary part replacements.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret the given circuit diagram of the inductive circuit
- Select equipment, tools and material required
- Prepare inductors and wires for termination
- Build a series-parallel inductive circuit
- Solder the built circuits
- Test the built inductive circuits
- Clean work area, tools and equipment
- Store tools, equipment and excess materials
Tathmini ya matokeo
The inductive circuits constructed as per technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Construct inductive circuits
- Identify an inductor
- Calculate the value of inductance
Principles: The student should explain the principles of:
- Constructing inductive circuits
- Carrying out measurement of voltage across an inductive circuit
Theories: The student should explain:
- The series-parallel inductive circuit and its behaviour
- The application of the various types of inductive circuit
Detailed knowledge about:
- Safety precaution in inductive circuits
- Safe handling of working tools, equipment and the inductors
Swali
What is a combined series-parallel circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado