Mada za sehemu hiiDetermining characteristic of active electronic devicesMada 5
A diode is a semiconductor device that allows current to flow in one direction only. Testing a diode's characteristics means checking whether it works properly and measuring the voltage across it when conducting current. In refrigeration and air conditioning equipment, diodes are used in control circuits and power supplies, so technicians must know how to test them.
What is a Diode?
A diode has two terminals:
- Anode — the positive terminal
- Cathode — the negative terminal (marked with a stripe)
The stripe on the diode body indicates the cathode side. When the anode is at a higher voltage than the cathode, the diode conducts (forward bias). When the cathode is at a higher voltage, the diode blocks current (reverse bias).
Forward Bias and Reverse Bias
Forward bias occurs when the positive terminal of a power supply is connected to the anode and the negative terminal to the cathode. Current flows through the diode. A small voltage (typically 0.6V to 0.7V for silicon diodes) develops across the diode.
Reverse bias occurs when the polarity is reversed. The diode does not conduct (except for a tiny leakage current). The diode blocks most of the voltage.
Testing a Diode with a Multimeter
Most digital multimeters have a diode testing mode. Follow these steps:
- Set the multimeter dial to the diode testing symbol (often a diode symbol with waves).
- Connect the red (positive) lead to the anode of the diode.
- Connect the black (negative) lead to the cathode of the diode.
- Observe the reading:
- Forward voltage: A reading between 0.5V and 0.8V indicates a good silicon diode conducting in the forward direction.
- No reading (infinite): If the display shows "1" or infinity in forward bias, the diode is open (faulty).
- Reverse voltage: If you reverse the leads, the meter should show "1" or infinity for a good diode. A low reading in reverse bias indicates a leaky or shorted diode.
Visual Inspection
Before using the meter, examine the diode physically:
- Check for physical damage, cracks, or burn marks.
- Verify the cathode stripe is visible and clear.
- Ensure the leads are not broken or corroded.
Worked Example
A student tests a diode using a multimeter in diode mode.
Step 1: Red lead to anode, black lead to cathode. The display reads 0.67V.
This is a normal forward voltage for a silicon diode. The diode is good.
Step 2: The student reverses the leads. The display reads 1 (infinite).
This is correct behavior — a good diode blocks reverse current.
Conclusion: The diode is functioning properly.
Testing a Diode in a Circuit
When testing a diode while it is still in a circuit:
- Power off the circuit completely.
- Disconnect one lead of the diode from the circuit to isolate it.
- Follow the multimeter procedure described above.
- If the diode cannot be isolated, note that other circuit components may affect the reading.
Common Diode Faults
- Open diode: Shows infinite resistance in both directions. Current cannot flow.
- Short diode: Shows very low resistance (near 0V) in both directions. The diode leaks current.
- Leaky diode: Shows a small voltage reading in reverse bias instead of infinity.
Safety Notes
- Always disconnect power before testing components.
- Wear gloves and an overcoat when handling electrical equipment.
- Work on a clean, dry work bench.
Real-life application
In Tanzania, refrigeration and air conditioning technicians often repair split air conditioners found in homes, shops, and offices. These units contain circuit boards with diodes that control the compressor and fan motors. When an air conditioner fails to turn on, a technician uses a multimeter to test the diodes on the circuit board to identify faulty components. This skill helps small business owners in Dar es Salaam and other regions reduce repair costs by avoiding unnecessary part replacements.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Select electronic components
- Construct circuit for Test characteristics of diodes
- Component testing
- Test electronic component
- Record test results
- Interpret standard test results
- Observe safety regulations
- Clean tools, equipment and workplace
- Store tools, equipment and components
Tathmini ya matokeo
Tested components bear characteristics that conform to specifications as given in component data books
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to test characteristics of diodes
Principles: The student should explain the principles of:
- Operating test equipment and measuring instruments Testing characteristics of diodes
Theories: The student should explain:
- Types of diodes
- The difference between passive and active electronic components
- Characteristics of diode in electronic
- Variation of component performance with temperature
Detailed knowledge about:
- Safety precautions in electronic work
- Safe handling of tools, test equipment and measuring instruments Safe handling of electronic components
Swali
What are the two terminals of a diode called?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado