Mada za sehemu hiiDetermining characteristic of active electronic devicesMada 5
Testing Characteristics of Transistors
A transistor is a small electronic component that acts as a switch or amplifier for electrical signals. It has three terminals: the base (which controls the switch), the collector (where current enters), and the emitter (where current leaves). In refrigeration and air conditioning systems, transistors are used in control circuits, sensors, and electronic boards. Testing a transistor means checking whether it is working properly or if it has developed a fault.
NPN Transistor
- The letter N stands for negative, and P stands for positive
- Current flows from collector to emitter when the base receives a small current
- The base is positive relative to the emitter
PNP Transistor
- Current flows from emitter to collector when the base is negative relative to the emitter
- The base is negative relative to the emitter
A digital multimeter in diode test mode or resistance mode can check the health of a transistor by testing its two PN junctions:
- Base-Collector junction — acts like a diode
- Base-Emitter junction — acts like a diode
A good transistor shows:
- A forward voltage drop of about 0.6V to 0.7V when the multimeter probes are placed across each junction (red probe on base, black on collector or emitter)
- A very high resistance (overload or "1") when the probes are reversed (reverse-biased)
Step 1: Identify the Transistor Type
Look for the part number on the transistor casing. Common transistors include:
- 2N2222 — NPN transistor
- 2N2907 — PNP transistor
If the part number is not visible, you can still test the junctions.
Step 2: Set the Multimeter
Turn the multimeter dial to diode test mode (often marked with a diode symbol). This mode supplies a small voltage to test the junctions.
Step 3: Test the Base-Collector Junction
- Place the red probe on the base of the transistor
- Place the black probe on the collector
- Observe the reading on the multimeter display
- A reading between 0.5V and 0.7V indicates a good forward-biased junction
- A reading showing "1" or overload means the junction is open (faulty)
- A reading of 0V means the junction is shorted (faulty)
Step 4: Test the Base-Emitter Junction
- Keep the red probe on the base
- Move the black probe to the emitter
- Observe the reading
- A reading between 0.5V and 0.7V means the junction is good
- Any other reading indicates a fault
Step 5: Test Reverse Bias
- Reverse the probes: black probe on base, red probe on collector, then on emitter
- The multimeter should show overload ("1") for both junctions
- If it shows a low voltage, the transistor is leaky or shorted
A student tests a 2N2222 NPN transistor using a digital multimeter set to diode mode.
| Test | Probe Placement | Expected Reading (Good Transistor) | Actual Reading | Result |
|---|---|---|---|---|
| 1 | Red on Base, Black on Collector | 0.6V to 0.7V | 0.65V | Good |
| 2 | Red on Base, Black on Emitter | 0.6V to 0.7V | 0.68V | Good |
| 3 | Black on Base, Red on Collector | Overload (1) | 1 | Good |
| 4 | Black on Base, Red on Emitter | Overload (1) | 1 | Good |
Conclusion: All four tests pass. The transistor is functioning properly and can be used in a circuit.
| Fault Symptom | Possible Cause |
|---|---|
| No reading in both forward and reverse tests | Open junction (transistor is dead) |
| 0V reading in both directions | Shorted junction |
| Low voltage reading when probes are reversed | Leaky transistor (current leakage) |
| Different readings for base-collector and base-emitter | Degraded transistor |
- Always disconnect power from the circuit before removing transistors
- Wear gloves and an overcoat when handling electronic components
- Work on a clean, dry work bench
- Handle transistors gently to avoid static damage
In Tanzania, transistors are found in the electronic control boards of air conditioning units commonly used in offices, shops, and guesthouses in Dar es Salaam and other cities. When an air conditioner stops working, a technician may use a multimeter to test the transistors on the circuit board to identify faulty components. For example, if the indoor fan motor does not run, checking the transistor that drives the fan motor can help determine whether the transistor needs replacement, saving the cost of replacing the entire control board which may cost over TSh 150,000.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Select electronic components
- Construct circuit for Testing characteristics of transistors
- Test electronic component
- Record test results
- Interpret standard test results
- Observe safety regulations
- Clean tools, equipment and workplace
- Store tools, equipment and components
Tathmini ya matokeo
Test components bear characteristics that conform to specifications as given in component data books
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to Test characteristics of transistors components
Principles: The student should explain the principles of:
- Operating test equipment and measuring instruments
- Testing components
Theories: The student should explain:
- Types of transistors in electronic components
- The difference between passive and active electronic components
- Variation of component performance with temperature
Detailed knowledge about:
- Safety precautions in electronic work
- Safe handling of tools, test equipment and measuring instruments Safe handling of electronic components
Swali
What are the three terminals of a transistor?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado