Mada za sehemu hiiDetermining characteristic of active electronic devicesMada 5
- Testing characteristics of diodes
- Testing characteristics of transistors
- Testing characteristics of thyristors
- Testing characteristics of opto-electronic devices
- Testing characteristics of integrated circuits
Opto-electronic devices are electronic components that either produce light or respond to light. In refrigeration and air conditioning systems, these devices are used for indicators, remote controls, and light-triggered switches. Testing their characteristics helps you understand how they work and diagnose faults in cooling equipment.
The most common opto-electronic devices you will test in practical work are:
- Light Emitting Diode (LED) — emits light when current flows through it; used as indicator lights on refrigerators and AC units
- Light Dependent Resistor (LDR) — its resistance changes with light intensity; used in light-sensing circuits
- Photodiode — conducts current when exposed to light; used in remote control receivers
- Infrared (IR) LED — emits invisible infrared light; used in air conditioner remote controls
Step 1: Identify the Leads
LEDs have two leads:
- The longer lead is the anode (positive)
- The shorter lead is the cathode (negative)
Step 2: Set the Multimeter
- Turn the multimeter dial to diode testing mode (usually shows a diode symbol)
- Connect the black lead to the cathode (short lead)
- Connect the red lead to the anode (long lead)
Step 3: Observe the Reading
A working LED will show:
- A forward voltage drop between 1.6V and 3.6V (typical values)
- The LED will emit visible light
If the display shows "1" or "OL" (open loop), the LED is damaged and will not light.
Worked Example
A refrigerator's door indicator LED fails to light. Using a multimeter in diode mode:
- Red lead to long lead, black lead to short lead
- Multimeter reads 2.1V and the LED glows
- Result: The LED is working correctly; the fault lies elsewhere in the circuit
Step 1: Measure Resistance in Darkness
- Set multimeter to resistance (Ω) mode
- Place the LDR in complete darkness (cover it with a cloth or place in a box)
- Record the resistance reading — typically 1 MΩ to 10 MΩ in darkness
Step 2: Measure Resistance in Light
- Expose the LDR to bright light (use a torch or sunlight)
- Record the resistance reading — typically 100 Ω to 1 kΩ in bright light
Step 3: Compare Results
A working LDR shows a large resistance change between dark and light conditions. If the resistance stays nearly the same, the LDR is faulty.
Air conditioner remote controls use IR LEDs to send signals. Testing requires:
- Set camera phone or digital camera to camera mode
- Point the remote control's IR LED at the camera
- Press any button on the remote
- Working IR LED: You will see a purple/white flash on the camera screen (invisible to the naked eye)
This test confirms whether the remote control is transmitting a signal.
- Wear gloves and overcoat when handling components
- Ensure the work bench is clean and free of metal objects that could cause short circuits
- Never connect LEDs directly to a power source without a current-limiting resistor
- Use safety goggles when testing components that may burst
| Symptom | Possible Cause |
|---|---|
| LED does not light | LED open-circuited or reversed polarity |
| LED lights but dim | Insufficient current or failing LED |
| LDR resistance does not change | Device damaged or contaminated surface |
| Remote control not detected | Weak battery or IR LED failed |
In Tanzania, when the indicator light on a shop's display refrigerator stops working, a technician uses a multimeter to test the LED by checking its forward voltage. If the LED shows the correct voltage (about 2V) but does not light, the technician knows to replace the LED. This skill is also needed when troubleshooting air conditioner remote controls — checking whether the IR LED emits a signal using a phone camera helps determine if the remote needs new batteries or repair.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Select electronic components
- Construct circuit for test characteristics of opto-electronic devices
- Test electronic component
- Record test results
- Interpret standard test results
- Observe safety regulations
- Clean tools, equipment and workplace
- Store tools, equipment and components
Tathmini ya matokeo
Test components bear characteristics that conform to specifications as given in component data books
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to test characteristics of opto-electronic devices
Principles: The student should explain the principles of:
- Operating test equipment and measuring instruments
- Testing components
Theories: The student should explain:
- Types of optoelectronic devices
- Characteristics of optoelectronic devices
- Variation of component performance with temperature
Detailed knowledge about:
- Safety precautions in electronic work
- Safe handling of tools, test equipment and measuring instruments Safe handling of electronic components
Swali
When testing an LED with a multimeter in diode mode, which lead should be connected to the black (common) probe?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado