Mada za sehemu hiiRepairing domestic freezersMada 4
- Replacing evaporator coil
- Replacing compressor unit
- Replacing temperature control
- Charging with refrigerant
Replacing a Compressor Unit in a Domestic Freezer
The compressor is the heart of a refrigeration system. It pumps refrigerant through the entire system to create the cooling effect. When a compressor fails, the freezer stops cooling. Replacing the compressor is a skilled repair task that involves recovering refrigerant, removing the old unit, installing a new one, and testing the system. This procedure must be done carefully to ensure safety and proper operation.
Before starting any work on a refrigeration system, always observe these safety rules:
- Wear safety boots, overalls, gloves, and goggles at all times
- Ensure the area is well-ventilated
- Never work on a system that is still pressurized
- Use proper refrigerant recovery equipment — never release refrigerant into the atmosphere
- Keep a fire extinguisher nearby when using oxy-acetylene welding equipment
- Disconnect power supply before working on electrical components
The following tools and equipment are needed for this task:
- Electro mechanical tool kit (screwdrivers, wrenches, pliers)
- Digital or analog multimeter (for electrical testing)
- Oxy-acetylene welding set (for brazing connections)
- Gauge manifold (to measure pressure)
- Vacuum pump (to remove moisture and air from the system)
- Refrigerant leak detector (to check for leaks)
- Recovery unit and recovery cylinder (to safely capture old refrigerant)
- Refrigerant identifier (to verify correct refrigerant type)
- Compressor valve key (to open and close service valves)
Step 1: Diagnose and Plan
- Confirm the compressor is faulty by checking that the freezer does not cool, the compressor motor does not run, or you hear unusual noises
- Identify the correct replacement compressor model that matches the original specifications
- Ensure the correct refrigerant type and quantity are available
Step 2: Recover the Refrigerant
- Connect the recovery unit to the service valves
- Follow the recovery unit manufacturer's instructions
- Transfer the old refrigerant into the recovery cylinder
- Verify the refrigerant has been fully recovered before proceeding
Step 3: Isolate and Remove the Old Compressor
- Close the suction and discharge service valves using the compressor valve key
- Disconnect the electrical wiring from the compressor terminals — use the multimeter to confirm power is off
- Carefully cut the suction and discharge lines using appropriate cutting tools
- Remove the mounting bolts holding the compressor in place
- Carefully lift out the old compressor
Step 4: Install the New Compressor
- Position the new compressor securely on its mounting
- Connect the suction and discharge lines to the new compressor using oxy-acetylene brazing
- Ensure all brazed joints are clean and properly made
- Reconnect the electrical wiring to the correct terminals — match the colours or refer to the wiring diagram
Step 5: Evacuate the System
- Connect the gauge manifold and vacuum pump to the service valves
- Open both valves and run the vacuum pump for at least 30 minutes
- Close the valves and check that the system holds vacuum — this confirms there are no leaks
- If vacuum is lost, check for leaks and repair before continuing
Step 6: Charge with Refrigerant
- Connect the refrigerant cylinder to the gauge manifold
- Use the refrigerant identifier to confirm the correct refrigerant type
- Charge the system with the specified amount of refrigerant
- Monitor the pressures on the gauge manifold to ensure proper readings
Step 7: Test for Leaks and Operation
- Use the leak detector to check all joints and connections
- If any leak is detected, repair it and repeat the evacuation process
- Power on the freezer and allow it to run
- Check that the compressor runs smoothly and the freezer reaches proper temperature
- Verify there are no unusual noises or vibrations
- Always recover refrigerant properly — releasing it harms the environment and is illegal
- The new compressor must match the original specifications (voltage, refrigerant type, and capacity)
- All brazed joints must be leak-free before proceeding to charging
- Proper evacuation removes moisture and air that would cause problems later
- Always test the system thoroughly after replacement before considering the job complete
A domestic freezer in a shop in Arusha has a faulty compressor. The technician follows these steps:
- Recovers 150g of R-134a refrigerant using the recovery unit
- Removes the old 1/5 HP compressor
- Installs a new 1/5 HP compressor rated for R-134a
- Braze the connections and evacuate the system for 45 minutes
- Charges with 150g of R-134a refrigerant
- Tests — the freezer reaches -18°C within 2 hours with no leaks
The shop owner pays TZS 180,000 for the repair, which is much cheaper than buying a new freezer.
In Tanzania, refrigerators and freezers are essential for households, shops, fish markets, and small businesses that sell perishable goods like milk, meat, and vegetables. When a compressor fails, knowing how to replace it allows a technician to restore a freezer quickly, saving the owner from buying expensive new equipment. This skill is valuable in towns like Mwanza, Dar es Salaam, and Dodoma where many small traders depend on cold storage for their livelihoods.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Perform diagnostic trouble shooting
- Replace compressor
- Repair scroll compressor
- Charge refrigerant
- Test run
- Clean workplace
- Store tools and equipment
Tathmini ya matokeo
Demonstrate the ability of identify size of compressor and replacing compressor in domestic freezer conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Control refrigerant being charged
- Measure compressor electrical and mechanical party
- Perform leak detection
- Join copper tubing
Principles: The student should explain the principles of:
- Heat transfer
- Basic refrigerant cooling cycle
- Scroll compressors
- Reciprocating compressors
Theories: The student should explain:
- Replace concept
Detailed knowledge about:
- Different refrigerant application
- Refrigerant properties Safe handling of refrigerants and tools
Swali
What is the primary function of the compressor in a refrigeration system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado