Mada za sehemu hiiRepairing domestic freezersMada 4
- Replacing evaporator coil
- Replacing compressor unit
- Replacing temperature control
- Charging with refrigerant
Charging with Refrigerant
Charging with refrigerant is the process of adding the correct amount of refrigerant into a refrigeration system after it has been repaired or when the refrigerant has been lost due to a leak. This is a critical skill for anyone repairing domestic refrigerators and freezers in Tanzania.
A refrigerant is a special fluid that absorbs heat from the inside of a refrigerator and releases it outside, making the interior cold. It circulates through the system in a continuous cycle, changing between liquid and gas states.
Common refrigerants used in domestic refrigerators
- R-134a – Used in many modern refrigerators
- R-600a (Isobutane) – Used in smaller domestic refrigerators
- R-12 – Found in older systems (CFC-based, now largely phased out)
A refrigeration system may need charging when:
- A leak has been repaired
- The system has been opened for component replacement
- The refrigerant has been lost during maintenance
Important: Before charging, the system must be properly evacuated (vacuumed) to remove air and moisture, otherwise the system will not work efficiently.
The following tools are required:
- Gauge manifold – Measures high and low pressure
- Charging scale – Measures the exact amount of refrigerant added
- Vacuum pump – Removes air and moisture before charging
- Refrigerant cylinder – Contains the correct refrigerant type
- Leak detector – Checks for leaks after charging
- Safety gear – Safety boots, overalls, gloves
Follow these steps carefully:
Step 1: Prepare the System
- Complete all repairs and leak fixes
- Connect the gauge manifold to the service ports
- Ensure the system is sealed and ready
Step 2: Evacuate the System
- Connect the vacuum pump to the manifold
- Run the vacuum pump for at least 15–30 minutes
- This removes air and moisture that would cause problems
Step 3: Weigh the Refrigerant
- Place the refrigerant cylinder on the charging scale
- Record the initial weight
- Calculate how much refrigerant the system requires (usually indicated on the equipment nameplate)
Step 4: Charge the Refrigerant
- Open the low-side valve on the manifold slowly
- Allow refrigerant to enter the system as a gas (not liquid)
- Watch the charging scale to know when the correct amount has been added
- Close the valve when the target weight is reached
Step 5: Check for Leaks and Operation
- Use a leak detector to check all joints and connections
- Start the compressor and let the system run
- Check that the low-side pressure is within the normal range (for R134a, typically 15–30 psi at normal room temperature)
- Verify that the freezer reaches the correct temperature
- Always wear safety boots and overalls when handling refrigerants
- Work in a well-ventilated area – refrigerants can displace oxygen
- Never overcharge the system – this causes high pressure and poor performance
- Do not release refrigerants into the atmosphere – they are harmful to the environment
- Keep sparks and open flames away from the work area
A domestic freezer using R-134a requires 150 grams of refrigerant. The technician weighs the refrigerant cylinder before charging and finds it reads 2,450 grams. After charging, the scale reads 2,300 grams.
Calculation:
- Initial weight: 2,450 g
- Final weight: 2,300 g
- Amount added: 2,450 – 2,300 = 150 grams
This matches the required amount, so the charging is complete.
Charging a refrigeration system requires:
- Proper preparation and evacuation
- Using accurate weighing (charging scale) to add the correct amount
- Checking for leaks and proper operation after charging
- Following all safety procedures to protect yourself and the environment
When done correctly, the refrigerator or freezer will run efficiently and maintain the desired cold temperature.
In Tanzania, many technicians repair domestic refrigerators and freezers in towns like Arusha, Mwanza, and Dar es Salaam. After fixing a leaking freezer, a technician must charge it with the correct amount of refrigerant using a charging scale — for example, charging R-134a worth about TZS 15,000–25,000 depending on the amount needed. Without proper charging, the freezer would not cool, and the customer's food would spoil, causing loss of money and food.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Perform diagnostic trouble shooting
- Check refrigerant leaks
- Repair refrigerant circuit coils
- Repair damaged cabinet
- Charge refrigerant
- Test run
- Clean workplace
- Store tools and equipment
Tathmini ya matokeo
Demonstrate the ability of charging required amount of refrigerant in freezer and charge with refrigerant in domestic freezer conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Control refrigerant being charged into freezer
- Identify refrigerant ozone global warming free
- Measure freezer pressure in pressure units
- Perform leak detection
Principles: The student should explain the principles of:
- Heat transfer
- Basic refrigerant cycle
Theories: The student should explain:
- Freezing concept
- Properties of refrigerant gas
- Sub cooling and super heating
Detailed knowledge about:
- Different refrigerant application
- Refrigerant properties
- Safe handling of refrigerants and tools
Swali
What is the primary function of a refrigerant in a domestic refrigerator?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado