Mada za sehemu hiiRepairing domestic freezersMada 4
- Replacing evaporator coil
- Replacing compressor unit
- Replacing temperature control
- Charging with refrigerant
Replacing Evaporator Coil
An evaporator coil is a key component in a domestic refrigeration system (such as a freezer or refrigerator). It is a coil made of copper tubes with fins that absorbs heat from the inside of the cabinet. The coil contains cold refrigerant that evaporates (changes from liquid to gas) as it absorbs heat, thereby cooling the interior of the freezer.
The evaporator coil is typically located inside the freezer compartment, usually at the back wall or behind the freezer liner. When the refrigerant inside the coil evaporates, it draws heat from the food and air inside the freezer, keeping the temperature low enough to preserve food.
The evaporator coil may need replacement when:
- Refrigerant leak – the coil develops a leak due to corrosion, physical damage, or age
- Blockage – the coil becomes blocked with ice, dirt, or debris, reducing its ability to absorb heat
- Physical damage – the coil is dented, crushed, or has broken fins that affect performance
- Poor cooling – the freezer fails to maintain proper temperature even after charging with refrigerant
Before starting any work on refrigeration systems, always observe these safety measures:
- Wear safety boots and overalls to protect your body
- Ensure the power supply to the freezer is disconnected before opening the system
- Handle refrigerants with care – they can cause frostbite on contact with skin
- Use proper lifting techniques when moving heavy components
- Keep the work area clean and free of oil, grease, or water
- Never use open flames near refrigeration systems – refrigerant gas can be flammable
Gather the following tools before starting:
- Electro-mechanical tool kit (screwdrivers, wrenches, pliers)
- Gauge manifold set
- Vacuum pump
- Refrigerant leak detector
- Hand drill machine
- Rivet gun
- Oxy-acetylene welding set (for brazing connections)
- Replacement evaporator coil
- Safety boots and overalls
Step 1: Disconnect Power and Remove the Freezer Contents
Unplug the freezer from the electrical supply. Remove all food items and store them in another freezer or cooler. Open the freezer door to allow the ice to melt, or use a heat gun to speed up defrosting if necessary.
Step 2: Access the Evaporator Coil
Remove the back panel or liner of the freezer to expose the evaporator coil. Carefully unscrew or unclip the panel. Take note of how the coil is mounted so you can install the new one correctly.
Step 3: Recover Existing Refrigerant
Connect the gauge manifold to the service ports on the compressor. Carefully recover any remaining refrigerant into a recovery cylinder. Never release refrigerant into the atmosphere – this is harmful to the environment and illegal.
Step 4: Disconnect the Old Coil
Use appropriate tools to disconnect the refrigerant lines (suction line and liquid line) from the evaporator coil. If the connections are brazed, use the oxy-acetylene welding set to heat and disconnect them safely. Remove any mounting brackets or rivets holding the coil in place.
Step 5: Install the New Evaporator Coil
Position the new evaporator coil in the correct location, ensuring it matches the original orientation. Secure it with mounting brackets or rivets. Connect the refrigerant lines to the correct ports on the new coil and braze the connections using the oxy-acetylene welding set.
Step 6: Check for Leaks
Use the refrigerant leak detector to check all brazed connections for leaks. If any leak is detected, re-braze the joint and test again until no leak is found.
Step 7: Evacuate the System
Connect the vacuum pump to the system through the gauge manifold. Run the vacuum pump for at least 30 minutes to remove all air and moisture from the system. Close the manifold valves and check that the vacuum holds.
Step 8: Charge with Refrigerant
Connect the refrigerant cylinder to the gauge manifold. Charge the system with the correct amount of refrigerant as specified by the manufacturer. Use the gauge manifold to monitor the pressures and ensure they are within the normal operating range.
Step 9: Test the System
Plug the freezer back in and allow it to run for several hours. Check that the freezer is cooling properly and that the temperature inside reaches the correct level (typically -18°C for a freezer). Monitor the system for any unusual noises or vibrations.
Step 10: Reassemble the Freezer
Once the system is working correctly, reattach the back panel or liner. Return the food items to the freezer and ensure the door seals properly.
A domestic freezer in a household in Arusha is not cooling properly. The technician checks the system and finds a refrigerant leak at the evaporator coil. The coil is old and corroded, so replacement is necessary.
Procedure followed:
- Power disconnected, food removed, and ice allowed to melt
- Back panel removed to access the evaporator coil
- Refrigerant recovered using gauge manifold
- Old coil disconnected after heating brazed joints with oxy-acetylene torch
- New coil installed and secured with rivets
- Connections brazed and leak tested – no leaks found
- System evacuated for 30 minutes using vacuum pump
- Refrigerant charged to correct pressure
- Freezer tested – temperature dropped to -18°C within 4 hours
- Panel reattached and freezer returned to customer
The freezer now works properly, and the customer's food is preserved safely.
- Incorrect coil size – always use the exact replacement specified by the manufacturer
- Poor brazing – ensure all joints are properly sealed to prevent refrigerant leaks
- Insufficient evacuation – never skip the vacuuming step; moisture in the system causes problems
- Overcharging or undercharging refrigerant – follow manufacturer specifications exactly
- Forgetting to check the condenser coil – a dirty condenser can cause similar cooling problems
In Tanzania, many households and small businesses (such as fishmongers, butchers, and small shops) rely on domestic freezers to preserve food. When an evaporator coil fails, the food inside can spoil, causing financial loss. A technician trained to replace evaporator coils can help local communities by repairing these freezers quickly and affordably. For example, a fish vendor at the Mwanza fish market can save tens of thousands of shillings in lost stock by having a faulty freezer coil replaced instead of buying a new appliance.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Perform diagnostic trouble shooting of evaporator coils
- Apply copper tubing bending technique
- Replace evaporator coil
- Riveting evaporator coil
- Charge refrigerant
- Test run
- Clean workplace
- Store tools and equipment
Tathmini ya matokeo
Demonstrate the ability of identify fault of evaporator coils and replace evaporator coils in domestic freezer conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Control refrigerant being charged
- Perform leak detection
- Join copper tubing
Principles: The student should explain the principles of:
- Basic refrigerant cooling cycle
Theories: The student should explain:
- Replace concept
Detailed knowledge about:
- Different copper tube application
- Refrigerant properties
- Piping circuits Safe handling of refrigerants and tools
Swali
What is the primary function of an evaporator coil in a domestic freezer?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado