Mada za sehemu hiiRepairing domestic refrigeratorsMada 6
- Repairing evaporator
- Repairing control equipment
- Repairing electrical circuit
- Repairing/replacing compressor
- Replacing door gasket
- Replacing default electronic card
Replacing Default Electronic Card in Domestic Refrigerators
A default electronic card (also called an electronic control board or PCB - Printed Circuit Board) is the "brain" of a modern domestic refrigerator. It is a flat circuit board with electronic components that controls the operation of the compressor, evaporator fan, condenser fan, and defrost system. When this card develops faults, the refrigerator may fail to cool properly, run continuously, or stop working altogether. This study note explains how to identify, safely remove, and install a replacement electronic card in a domestic refrigerator.
An electronic card is a small circuit board mounted inside the refrigerator's control panel or behind the kick plate at the bottom of the unit. It receives signals from temperature sensors and user controls, then sends electrical commands to:
- Start and stop the compressor
- Operate the condenser and evaporator fans
- Control the defrost heater and timer
- Run the ice maker (if equipped)
Without a functioning electronic card, the refrigerator cannot regulate its internal temperature.
Before replacing the card, a technician must confirm the fault. Common signs include:
- Refrigerator does not start at all (no cooling)
- Compressor runs continuously without stopping
- Interior light works but the refrigerator does not cool
- Erratic freezing or overheating
- Fault codes displayed on the panel (for digital models)
- Fans run but compressor does not start
Note: Always check power supply, door seals, and temperature settings first before concluding the electronic card is faulty.
Working with electrical components requires strict safety measures:
- Disconnect power — Unplug the refrigerator from the socket or switch off the circuit breaker before starting any work.
- Wear protective gear — Put on safety boots and overalls to protect against sharp edges and electrical shock.
- Allow capacitor discharge — High-voltage run capacitors can retain dangerous charge. Use a multimeter to confirm no voltage before touching components.
- Avoid static discharge — Static electricity can damage electronic components. Touch a grounded metal surface before handling the card.
- Work in a dry area — Ensure the floor is dry to prevent slipping and electrical hazards.
- Electro-mechanical tool kit (screwdrivers, pliers, wire strippers)
- Digital or analog multimeter
- Leak detector (for checking refrigerant if lines are disturbed)
- Small painting soft brush (for cleaning dust and debris)
- Safety boots and overalls
Step 1: Diagnosis and Identification
- Observe the refrigerator's behavior and note any fault symptoms.
- Use the multimeter to check power supply voltage at the outlet (should be 220-240V in Tanzania).
- Locate the electronic card and check for visible damage such as burnt components, blown fuses, or swollen capacitors.
- Match the part number of the existing card with a new replacement suitable for the refrigerator model.
Step 2: Access the Electronic Card
- Unplug the refrigerator from the power source.
- Remove the lower kick plate or back panel to expose the electronic card.
- Use a screwdriver to carefully remove the panel cover.
Step 3: Document Connections
- Take a clear photograph of the card and all wire connectors before disconnecting anything.
- Note the position of each wire connector to ensure correct reconnection later.
Step 4: Remove the Faulty Card
- Disconnect each wire connector by releasing the locking tabs (do not pull wires).
- Unscrew the mounting screws holding the card in place.
- Gently lift the card out of its housing.
Step 5: Install the Replacement Card
- Place the new electronic card in the same position as the old one.
- Secure it with the mounting screws.
- Reconnect each wire connector to its original position, ensuring they click into place.
- Double-check all connections against your photograph.
Step 6: Test the System
- Plug the refrigerator back into the power supply.
- Observe the refrigerator as it starts up.
- Listen for the compressor to start and check that the fans are running.
- Allow 30 minutes to 1 hour for the cabinet to cool down, then verify normal operation.
A customer's frost-free refrigerator in Arusha is showing the following symptoms: the compressor will not start, but the interior light works and the evaporator fan runs normally. The customer has already checked that the power socket is working correctly.
Analysis:
- Since the fan runs but the compressor does not start, the fault likely lies with the electronic control card or the compressor overload protector.
- After testing the overload protector with a multimeter and finding it normal, the technician concludes the electronic card is faulty.
Action:
- Switch off power and remove the lower kick plate.
- Photograph the wiring connections.
- Disconnect and remove the faulty electronic card.
- Install a new card with the correct part number.
- Reconnect all wires, restore power, and verify the compressor starts and the refrigerator cools normally.
This procedure restores the refrigerator to proper working condition.
- The electronic card controls all major operations in modern refrigerators.
- Always disconnect power before working on any electrical component.
- Photograph and label connections before disconnecting wires.
- Use the correct replacement card matching the refrigerator's make and model.
- After replacement, test the refrigerator to ensure proper cooling.
In Tanzania, many households and small shops in areas like Mwanza, Dodoma, and Mbeya depend on domestic refrigerators to preserve food, medicine, and shop goods such as sodas and fresh milk. When the electronic card fails, a technician with the skills to diagnose the fault and replace the card can repair the refrigerator on-site, saving the owner the cost of buying a new refrigerator (often costing TSh 500,000 to TSh 1,500,000). This practical skill also creates income-generating opportunities for young technicians in local communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Perform diagnostic trouble shooting
- Repair refrigerant leaks
- Repair electric wiring
- Remove damage electronic card
- Repair non-frost electric control circuits
- Repair damaged cabinet
- Replacing electronic card
- Connect electronic card
- Test run
- Clean workplace
- Store tools and equipment
Tathmini ya matokeo
Demonstrate the ability of identify fault of electronic card and replace electronics card in electronics card conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Measure electric quantities
Principles: The student should explain the principles of:
Theories: The student should explain:
- Repair concept
- Material science
Detailed knowledge about:
- Different refrigerant application
- Refrigerant properties
- Electrical circuits
- Safe handling of refrigerants and tools
Swali
Which of the following components is controlled by the electronic card in a domestic refrigerator?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado