Mada za sehemu hiiPerforming quality control of woven fabricMada 4
- Inspecting woven fabric
- Taking process (weaving) correction measures
- Mending minor faults
- Grading woven fabrics
Inspecting woven fabric is the process of examining finished fabric to identify defects, determine quality, and mark faulty areas before the fabric is processed further or sold. This quality control step ensures that only acceptable fabric reaches customers.
Woven fabric faults are abnormalities that occur during the weaving process. These faults ruin the appearance and reduce the overall quality of the woven fabric. They also cause major defects in the garment industry and lead to loss of time and resources. Timely detection and corrective measures ensure fabrics meet customer requirements.
Faults in woven fabrics originate from two main sources:
1. Faulty Yarns
Yarn defects such as neps, thick and thin places, foreign particles, and twist variations can lead to fabric defects. These create streaks, specks, stripes, and other visual groupings on the fabric. Thin and thick places in yarn cause strength variation along the yarn length, resulting in patchy defective fabrics.
2. Incorrect Loom Settings
Improper settings of weaving parameters on the loom cause fabric defects. Examples include:
- Improper warp tension
- Improper denting (spacing of warp yarns in the reed)
- Wrong treading (incorrect heddle threading)
To ensure quality fabric, the yarn must be good and loom settings must be appropriate.
Warp Streaks
Narrow, bare, and dense stripes running along the warp direction. Caused by variation in density of adjacent warp ends from non-uniform dent spacing, wrong drawing-in, or count variations.
Reedness
Very fine cracks or lines between groups of warp yarns. Caused by excessive warp tension, late shedding, coarse reed, bent reed wires, or improper reed wire spacing.
Reed Mark
A pronounced crack between groups of warp ends caused by damaged or defective reed or improper dent spacing.
Weft Bar
An unwanted band running weft-wise across the fabric width. Caused by irregularities in weft yarns—variations in yarn count, twist, or colour from different cones. Also caused by faulty let-off and take-up motions.
Float
A defect where warp and weft yarns escape their required interlacement. Main causes are slack warps and entangling of broken yarns with other yarns.
Thin and Thick Places
- Thin place: Where weft density is smaller than surrounding areas
- Thick place: Where yarns are more closely spaced or thick yarns are congested
Caused by poor yarn quality, irregular take-up settings, and improper let-off motion.
Knots
Defects caused by improper knotting when joining broken yarns during spinning or weaving.
Slubs
Short, thick, or heavy places on yarns that create a lumpy appearance on fabric. Both knots and slubs can be prevented by using high-quality yarns.
Broken Ends (Warp)
A broken warp yarn during weaving, caused by failure to apply warp break properly.
Missing Pick
A fabric defect where the loom starts without picking the broken weft, resulting in a full-width gap without weft yarn.
Bad or Defective Selvedge
Curls and folds in the fabric edge. Caused by improper shuttle wire tension, bent shuttle jaw, late shedding, or wrong selvedge-weave selection.
| Tool | Purpose |
|---|---|
| Inspection table | Illuminated table for examining fabric over a wide area while rotating |
| UV lamp | Provides bright light to spot minor defects |
| Pick (magnifying) glass | Identifies details of minor defects not visible to naked eye |
| Measuring tape | Measures fabric width and length |
Activity 3.3: Inspecting a woven fabric for quality and marking faulty areas
Steps:
- Collect fabric samples
- Lay the fabric on the inspection table, one at a time
- Inspect the fabric from different angles using proper lighting
- Mark faults using a marker, paper tape, or stickers
- Describe the faults observed and their possible causes
A weaver inspects a fabric roll and finds the following defects:
- 2 warp streaks (each 5 cm long)
- 1 float defect (8 cm long)
- 1 small hole (2 cm diameter)
Solution:
- Warp streaks: Mark both areas with tape and note the location
- Float: Mark the floating yarn area
- Hole: Mark the hole with a sticker
The inspector records each defect type, size, and location. This information helps determine whether the fabric can be mended, requires price reduction, or should be rejected.
During fabric inspection, always:
- Work in good lighting (natural light or UV lamp)
- Examine both fabric faces
- Check selvedges carefully
- Measure defect sizes accurately
- Mark all defects clearly for mending or grading
In Tanzania, weavers at local weaving cooperatives in places like Tanga, Morogoro, or Arusha use fabric inspection to determine the quality of their products before selling them at markets such as Kariakoo or Mwalimu Nyerere Airport duty-free. A detected defect like a weft bar or bad selvedge allows the weaver to either mend it, sell it at a lower price, or use it for a different product, helping the business avoid losses and maintain customer satisfaction.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to: A Process
- Select tools and equipment
- Observe safety precautions
- Check process parameters during winding, warping, weaving,
- Inspect finished products
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
A woven fabric is properly inspected
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to: inspect woven fabric for defects
Principles: The student should explain the principles of inspecting woven fabric for defects
Theories: The student should explain:
- Major areas of process and quality control in handloom weaving operations
- Stages of quality control
Circumstantial knowledge: Detailed knowledge of:
- Safe handling of working tools and materials
- Safe handling of measuring instruments
- Environmental management standards
Swali
What are woven fabric faults?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado