Mada za sehemu hiiPerforming quality control of woven fabricMada 4
Mending Minor Faults in Woven Fabric
When woven fabrics come off the loom, they often have small imperfections caused by the weaving process. These faults must be identified, repaired, and corrected before the fabric is sold or processed further.
Mending is the process of repairing or fixing faults that occur in a fabric. Freshly produced woven fabrics usually have imperfections that arise during production. If these faults are not corrected in time, they can result in severe losses to the manufacturer. Therefore, woven fabric is first inspected, faults are marked, and then minor faults are repaired using mending tools before the fabric is sent to the customer or undergoes further processing.
The main tools used to mend woven fabrics are:
- Clippers — used for cutting loose or protruding yarns
- Pluckers or pins — used for removing foreign objects and pulling out extra yarn ends
- Combs (wooden, plastic, or metallic) — used for filling bare patches by combing in both directions
Most minor faults can be mended. However, some faults cannot be repaired and the fabric is simply graded lower. Examples of non-mendable faults include:
- Broken patterns
- Knots
- Major holes
- Weft bars
- Reed marks
Once faults have been identified and marked, follow these mending procedures:
1. Coloured and Non-Coloured Foreign Matters
- Use a plucker to remove foreign objects from the fabric
- Use a comb or pin to comb in both directions and fill the resulting bare patch
2. Slubs
- Cut the slub with a clipper from both ends
- Pull off the bulk yarn by using a plucker
- The resultant bare patch can be corrected by combing with a metallic comb or by inserting a separate yarn with the help of a fine needle
3. Broken Ends
- Remove the broken end using a plucker or a pin
- Cut the resulting loose ends using a clipper
- Use a metallic comb or pin to comb in both directions and fill the resulting bare patch
4. Double End
- Use a pin to pull out the extra end
- Use a metallic comb or pin to comb in both directions and fill the resulting bare patch
5. Missing Picks or Missing Ends
If two adjacent picks or ends are missing, the fault can be corrected by combing in both directions using a metallic comb or pin.
6. Floats
Minor floats can be corrected by:
- Cutting the floating yarn using a clipper
- Using a metallic comb or pin to comb in both directions and fill the resulting bare patch
7. Oils or Other Stains
- Keep the stained portion of the fabric over an absorbent pad
- Apply stain remover (soap and water) to wet the stain and surrounding areas to allow the remover to penetrate
- Rinse off the fabric with clean water
- Squeeze off any excess water and hang the fabric to dry
- Iron to remove wrinkles
When performing mending in class, follow these steps:
- Collect tools and equipment (clippers, pluckers, combs, inspection table)
- Lay down the fabric that has been marked for faults during inspection
- Mend the marked faults using the appropriate procedure from Table 3.4 above
- Check that the mend is neat and does not create new faults
In Tanzania, small-scale handloom weavers in districts like Bagamoyo, Tanga, and Shinyanga use mending skills to repair minor defects in their fabrics before selling them at local markets or to tourists. A weaver who can mend faults competently can sell a fabric that would otherwise be discarded, saving materials and increasing income — for example, repairing a float defect on a kitenge cloth worth TZS 15,000 instead of losing the entire piece.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to appropriately:
- Select tools
- Observe safety precautions equipment
- Inspect finished products
- Mend the minor faults
- Clean tools and equipment
- Store tools and equipment A Process
Tathmini ya matokeo
The minor faults in woven fabrics are properly mended
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to mend minor faults
Principles: The student should be able to explain the principles of mending minor faults
Theories: The student should explain
- different procedures to mend minor faults on woven fabric
Circumstantial knowledge: Detailed knowledge of:
- Safe handling of working tools and materials
- Safe handling of measuring instruments
- Environmental management standards
Swali
Which of the following tools are used for mending minor faults in woven fabric?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado