Mada za sehemu hiiPerforming pointing and jointingMada 4
- Pointing a masonry work / stonework
- Pointing a block wall
- Pointing a brick wall
- Performing jointing
Pointing a Block Wall
Pointing is the process of finishing the mortar joints between bricks or blocks in masonry work. It involves filling the gaps with mortar and shaping it to improve the structure's appearance, durability, and weather resistance.
Pointing serves three important functions:
- Weather resistance – properly pointed joints prevent water penetration into the wall
- Structural integrity – it strengthens the bond between masonry units
- Aesthetic appeal – it creates a neat, finished appearance that enhances the building's look
The textbook describes several types of pointing finishes:
Flush pointing – mortar is pressed flush with the brick or block surface. This is simple and economical but offers less weather resistance because water can accumulate on the mortar line.
Recessed pointing – mortar is pressed back (typically 5–10 mm) from the masonry surface. This creates shadow lines that highlight individual masonry units. It requires skilled craftsmanship and high-quality mortar.
Struck pointing – mortar is tooled at a downward angle (typically 30–45°) to create a water-shedding profile. This improves weather resistance by directing moisture away from the joint.
Weather-struck pointing – the top edge of the joint is deeply recessed and the mortar slopes steeply downward. This creates a shadow line and ensures water is shed immediately from the face of the joint.
V-groove pointing – a V-shaped channel (typically 3–5 mm deep) is tooled into the mortar joint. This creates sharp shadow lines that add visual depth and architectural character.
Tuck pointing – flush mortar joints are accented with precisely cut grooves filled with contrasting mortar or putty. This creates the illusion of perfect, thin joints.
Follow these steps carefully to point a block wall properly:
Step 1: Prepare the Surface
- Remove old or damaged mortar using a chisel and hammer
- Clean the joints and surfaces with a brush to remove dust and debris
- Dampen the joints with water to improve mortar adhesion
Step 2: Mix the Mortar
- Mix cement and sand in the recommended ratio (typically 1:3 – 1 part cement to 3 parts sand)
- Add water gradually while mixing until reaching a workable consistency
- Add waterproofing additives or pigments if required
- Ensure the mortar has a smooth, consistent texture
Step 3: Apply the Mortar
- Use a trowel to fill the joints with mortar
- Press the mortar firmly to eliminate air pockets
- Overfill the joints slightly to allow for shaping
Step 4: Shape the Finish
- Use a pointing tool or jointing iron to shape the mortar according to the desired finish (flush, recessed, V-groove, etc.)
- Smooth the surface and remove excess mortar
- Clean the masonry surface with a brush to remove any mortar stains
Step 5: Cure the Pointing
- Keep the pointed surface damp for 2–3 days to allow proper curing
- Protect the surface from direct sunlight and rain during this time
A student needs to point a block wall that has 15 square meters of joint area. The mortar ratio is 1:3 (cement:sand).
Given:
- Area to be pointed = 15 m²
- Mortar thickness for pointing = approximately 10 mm (0.01 m)
- Mix ratio = 1:3 (1 part cement to 3 parts sand)
Solution: Volume of mortar needed = Area × Thickness Volume = 15 m² × 0.01 m = 0.15 m³
For a 1:3 mix, total parts = 1 + 3 = 4 parts Cement needed = 0.15 ÷ 4 = 0.0375 m³ Sand needed = 0.15 × (3/4) = 0.1125 m³
In practice, you would add about 10-15% extra for wastage and shrinkage.
The following tools are essential for pointing work:
| Tool | Purpose |
|---|---|
| Pointing trowel | Filling joints with mortar |
| Pointing tool / Jointing iron | Shaping the mortar finish |
| Mortar hawk | Holding mortar while working |
| Brush | Cleaning joints and surfaces |
| Chisel and hammer | Removing old mortar |
| Spirit level | Checking alignment |
- Wear gloves when working with cement
- Wear boots to protect feet
- Wear overalls for body protection
- Wear a helmet when working at height
- Use safety gear when cutting or chiselling old mortar
- Applying mortar to dry joints – always dampen joints first for better adhesion
- Using too wet or too dry mortar – achieve a workable, consistent texture
- Not curing properly – keep the surface damp for 2–3 days
- Rushing the finishing – take time to achieve a neat, uniform appearance
In Tanzania, pointing is commonly used when building or renovating houses in rural and urban areas. For example, if a family in Mwanza builds a new house with concrete block walls, proper pointing of the joints will protect the walls from rain during the wet season and extend the building's lifespan. A skilled mason who masters pointing techniques can also offer services in the local market, earning income by pointing walls for neighbors or on construction sites in towns like Arusha or Dar es Salaam.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Prepare materials
- Prepare tools and equipment
- Prepare the Mortar
- Clean the Joints
- Dampen the Joints
- Carry out pointing works
- Remove Excess Mortar
- Perform curing
- Clean tools and store
Tathmini ya matokeo
Pointing of a block wall is performed as per finishing techniques to ensure structural integrity, prevent water ingress, improve aesthetics, and enhance durability
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should explain different methods of pointing
Principles: The student should explain the principles involved pointing a block wall
Theories: The student should explain:
- Pointing
- Types of pointing
- Curing
- Cost estimate Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while performing pointing and pointing
- First aid
- Environmental issues
Swali
What is the primary purpose of pointing in masonry work?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado