Mada za sehemu hiiPerforming pointing and jointingMada 4
- Pointing a masonry work / stonework
- Pointing a block wall
- Pointing a brick wall
- Performing jointing
Pointing is the process of finishing the mortar joints between bricks or blocks in masonry work. It involves filling the gaps with mortar and shaping it to improve the structure's appearance, durability, and weather resistance. When you point a brick wall properly, you prevent water from seeping into the building while making the wall look neat and attractive.
Pointing serves three main purposes:
- Weather resistance: Properly pointed joints prevent rainwater from penetrating the masonry, which could cause damage during rainy seasons
- Structural integrity: Well-finished joints strengthen the bond between bricks or blocks, making the wall more stable
- Aesthetic appeal: Pointing gives the wall a clean, finished appearance that enhances the overall look of a building
There are several types of pointing techniques, each giving a different visual effect:
Flush Pointing
The mortar is pressed flush with the brick surface. This is the simplest and most economical method. However, water can accumulate on the flat surface, making it less resistant to weather.
Recessed Pointing
The mortar is pressed back 5–10 mm from the brick surface. This creates attractive shadow lines that highlight individual bricks. It requires skilled craftsmanship and works best with high-quality mortar.
Struck Pointing
The mortar is first pressed flush, then tooled at a downward angle (typically 30–45°). This creates a sloped surface that sheds water away from the joint, improving weather resistance.
Weather-Struck Pointing
The top edge of the joint is deeply recessed, and the mortar surface slopes steeply downward. This is an advanced technique that provides excellent water shedding.
V-Groove Pointing
A V-shaped channel (3–5 mm deep) is tooled into the mortar joint. This creates sharp shadow lines and adds visual depth to the brickwork.
Tuck Pointing
Flush mortar joints are accented with narrow grooves (about 3 mm wide) filled with contrasting mortar or putty. This creates the appearance of very fine, precise joints.
Tools:
- Pointing trowel
- Pointing tool or jointing iron
- Mortar hawk
- Chisel and hammer
- Brush
- Spirit level
Materials:
- Mortar (cement and sand mixed in ratio 1:3)
- Water
- Waterproofing additives (optional)
- Pigments (optional, for coloured pointing)
Step 1: Prepare the Surface
Remove old or damaged mortar from the joints using a chisel and hammer. Clean the joints and brick surfaces with a brush to remove dust and debris. Dampen the joints with water—this improves mortar adhesion by preventing the dry brick from absorbing water from the fresh mortar too quickly.
Step 2: Prepare the Mortar
Mix cement and sand in a 1:3 ratio (1 part cement to 3 parts sand). Add water gradually while mixing until the mortar reaches a workable consistency—not too dry, not too wet. If required, add waterproofing additives or pigments and mix thoroughly to ensure uniform colour and texture.
Step 3: Fill the Joints
Load mortar onto a mortar hawk for easy access. Using a pointing trowel, press the mortar firmly into the joints to eliminate air pockets. Overfill the joints slightly to allow material for shaping and finishing.
Step 4: Shape the Joints
Use a pointing tool or jointing iron to shape the mortar according to the desired finish (flush, recessed, V-groove, or other). Work systematically along each joint, ensuring consistent depth and angle. Smooth the surface and remove excess mortar, then clean the brick surface with a brush to remove any mortar stains.
Step 5: Cure the Pointing
Keep the pointed surface damp for 2–3 days to allow proper curing. Protect the surface from direct sunlight and rain during this time. Cover with a damp cloth or plastic sheet if necessary to retain moisture.
Step 6: Clean Up
Thoroughly clean all tools after use and store them properly. Remove any mortar debris from the worksite.
- Wear gloves when handling cement and mortar
- Wear boots to protect feet
- Wear overalls for body protection
- Wear a helmet when working at height
- Use safety gear (goggles) when cutting or chipping old mortar
In Tanzania, pointing is commonly used when building or renovating houses in rural and urban areas. For example, if a family in Mwanza is constructing a new brick house for their home, proper pointing of the exterior walls will protect the building from the heavy rains common in the region while giving the house an attractive appearance that increases its value. Skilled masons who master pointing techniques can also earn income by offering these services to others in their community.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Prepare materials
- Prepare tools and equipment
- Prepare the Mortar
- Clean the Joints
- Dampen the Joints
- Carry out pointing works
- Remove Excess Mortar
- Perform curing
- Clean tools and store
Tathmini ya matokeo
Pointing of a brick wall is performed as per finishing techniques to ensure structural integrity, prevent water ingress, improve aesthetics, and enhance durability
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should explain different methods of pointing
Principles: The student should explain the principles involved pointing a block wall Theories: The student should explain:
- Pointing
- Types of pointing
- Curing
- Cost estimate Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while performing pointing and pointing
- First aid
- Environmental issues
Swali
What is the main purpose of pointing in masonry work?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado