Mada za sehemu hiiConstructing shoresMada 3
- Constructing racking and rider shores
- Constructing flying shore
- Constructing dead shores
Constructing Dead Shores
Dead shores are temporary structural supports used to hold up a building or part of a building during construction, renovation, or repair work. They are called "dead" shores because they are fixed, non-adjustable supports that bear loads permanently until the permanent structure can carry the weight on its own. Dead shores take the weight off walls, floors, or beams while workers make changes below or beside them.
Dead shores serve several important purposes in construction:
- Supporting walls during opening creation — When removing a wall to create a doorway or window, dead shores support the structure above
- Temporary support during repairs — When a wall or beam is damaged, dead shores hold the building safe while repairs are made
- Allowing foundation work — When underpinning or extending foundations, dead shores carry the load above
- Structural alterations — When removing load-bearing walls, dead shores bear the load temporarily until permanent beams are installed
A dead shore system consists of three main parts:
- Post (vertical member) — Strong timber post that carries the vertical load directly to the ground
- Beam (horizontal member) — Placed on top of the post to spread the load across the support
- Wedge or packing pieces — Small timber pieces used to make fine adjustments for tight fitting
The beam sits on top of the post, and the load from the structure above is transferred through the beam to the post, then to the ground.
For school practical work, dead shores are constructed using:
- Timber beams (strong hardwood, approximately 150mm × 75mm)
- Timber posts (approximately 100mm × 100mm hardwood)
- Wedges (small hardwood pieces for tightening)
- Nails (100mm or 125mm for securing joints)
The timber must be straight, free from cracks, and strong enough to support the expected load. In professional construction, steel posts and beams may also be used.
Step 1: Site Assessment and Planning
Before constructing dead shores, identify:
- The exact location where support is needed
- The load that the shores will carry
- The number of shores required based on the load
Step 2: Prepare the Site
- Clear the area where posts will stand
- Ensure the ground is firm and level
- Place base plates or sole plates under each post position to spread the load
Step 3: Measure and Cut Timber
- Measure the height from the ground to the underside of the beam that will receive the load
- Cut the timber posts to the required length, allowing a small gap for wedges
- Cut the beam to span across the area requiring support, extending at least 300mm beyond each side of the opening
Step 4: Erect the Posts
- Position the posts at each end of the planned beam location
- Use a spirit level to ensure each post is perfectly vertical
- Check with a plumb bob from the top to confirm alignment
Step 5: Position the Beam
- Place the horizontal beam on top of the posts
- Ensure the beam is level using a spirit level
- The beam must be centered and running perpendicular to the floor joists or wall above
Step 6: Install Wedges and Secure
- Drive wedges between the top of the post and the beam to create a tight fit
- Nail the beam to the posts on both sides to prevent movement
- Check that everything is stable and does not wobble
Step 7: Safety Checks
- Verify all connections are secure
- Ensure no gaps exist between the beam and the structure above
- Check that the shores are taking the weight (the beam should be slightly compressed)
When constructing dead shores, always wear:
- Hard helmet
- Safety boots
- Gloves
- Safety goggles
- High-visibility vest
Never work under a structure that is not properly supported. Dead shores must be checked regularly during use to ensure they remain tight and secure.
A contractor in Dar es Salaam needs to create a doorway through a 200mm thick load-bearing wall. The wall carries the weight of a concrete slab above. The opening will be 900mm wide.
Solution:
-
Calculate the required beam length: The opening is 900mm. Add 300mm on each side for support, so the beam length = 900mm + 300mm + 300mm = 1500mm (1.5m).
-
Determine post height: Measure from the floor to the underside of the concrete slab. If the measurement is 2800mm, cut the posts to 2750mm to allow 50mm for wedges.
-
Number of shores needed: Use two posts — one on each side of the opening.
-
Beam size: Use a 150mm × 75mm hardwood beam strong enough to carry the slab load.
-
Construction sequence: Follow the six-step process above, checking with a spirit level at each stage.
This dead shore system safely supports the wall while the new doorway is constructed, preventing collapse during the work.
Dead shores are essential temporary supports in construction. They consist of vertical posts and horizontal beams that transfer loads safely to the ground. When constructed correctly using proper materials, accurate measurements, and good fitting techniques, dead shores protect workers and prevent structural damage during building work.
In Tanzania, masons and builders use dead shores when renovating shops along streets like Msasani or in manyongo (rural market) buildings where a wall needs to be removed to widen a doorway. A small construction team in Arusha might erect dead shores to support the roof while they rebuild a damaged load-bearing wall, ensuring the building remains safe throughout the repair work. Understanding dead shore construction is therefore a valuable skill for anyone working in building trades across Tanzania.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Understand dead shores
- Interpret working drawings
- Measure and cut materials
- Assemble and install shores
- Ensure stability
- Dismantle safely and clean up
Tathmini ya matokeo
Dead shores are constructed according to structural specifications to provide temporary support during construction or repair work.
Tathmini ya maarifa
Detailed knowledge of:
Method used: The students should explain the procedures for constructing dead shores.
Principles: The student should explain the principles involved in constructing dead shores.
Circumstantial knowledge:
Detailed knowledge about:
- Materials and tools needed.
- Safety measures for working under support.
Swali
What does the term "dead" in "dead shores" refer to?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado