Mada za sehemu hiiConstructing eaves and bargeboardMada 5
Open eaves are the exposed lower edges of a sloping roof where the rafters extend beyond the wall plate, leaving the underside open to view. This design allows for ventilation in the roof space and gives a traditional appearance to buildings. In Tanzania, open eaves are commonly seen on residential houses, school buildings, and traditional structures.
Understanding the components helps in proper construction:
- Rafter tail – the extended portion of the rafter that projects beyond the wall
- Fascia board – a horizontal board fixed to the ends of the rafters to cover the edge
- Soffit board – the board fixed underneath the rafters, closing the gap between the fascia and the wall
- Wall plate – the horizontal timber anchored to the wall that supports the rafters
- Ridge board – the horizontal timber at the top where rafters meet
Tools:
- Try square, tape measure, sliding bevel
- Hand saw, chisels
- Claw hammer, mallet hammer
- Claw bar, manila line
- Spirit level, pencil
Materials:
- Timber rafters (sized according to span)
- Fascia board (typically 150mm × 25mm)
- Soffit board (typically 100mm × 19mm)
- Nails (galvanized)
Safety gear: Safety boots, safety helmet, and overalls must be worn at all times.
Step 1: Take Measurements
Measure the length of each rafter tail needed. The projection typically ranges from 300mm to 450mm depending on the roof design. Use a tape measure and mark the cut line on each rafter using a try square to ensure accuracy.
Step 2: Mark and Cut Rafters
Use a sliding bevel to set the correct angle for the rafter cut at the tail. Mark the position where the rafter will sit on the wall plate. Cut the rafters to size using a hand saw, ensuring all cuts are square and clean.
Step 3: Install the Wall Plate
Ensure the wall plate is level and securely fixed to the wall using appropriate fasteners. This provides a solid base for rafter installation.
Step 4: Fix the Rafters
Position each rafter on the wall plate at the correct spacing (usually 400mm to 600mm centre-to-centre). Nail the rafters firmly to the wall plate using claws or galvanized nails. Ensure all rafters are aligned and level.
Step 5: Install the Fascia Board
Fix the fascia board horizontally to the ends of the rafters. Use a spirit level to ensure it is perfectly horizontal. The fascia should be nailed securely to each rafter tail.
Step 6: Fix the Soffit Board
Cut the soffit board to fit between the fascia board and the wall. Fix it in place using nails, ensuring it is flush and provides a neat finish to the underside of the eaves.
A student constructing open eaves for a small domestic roof with a 3-metre projection:
- Measure the rafter tail length = 450mm
- Space rafters at 450mm centres along a 6-metre wall
- Number of rafters = (6000 ÷ 450) + 1 = 14 rafters
- Cut fascia board to 6 metres total length
- Fix all components maintaining level and alignment
- Always wear safety boots, helmet, and overalls on site
- Check all tools are in good condition before use
- Ensure ladders are stable before climbing
- Keep the work area clean and free from debris
- Use proper lifting techniques when handling timber
Open eaves construction involves extending rafters beyond the wall, fixing fascia and soffit boards to create a finished edge. Accurate measurement, proper alignment, and secure fixing are essential for a durable and visually appealing result.
In Tanzania, a carpenter with skills in constructing open eaves can help homeowners build or repair roof eaves on houses in areas like Mwanza, Arusha, or Dodoma, where many buildings use pitched roofs. For example, when a farmer in a village needs to extend the eaves of a storehouse to protect walls from rain, the carpenter can measure the required 400mm projection, cut and fix the rafters, fascia, and soffit boards, providing functional weather protection that costs the farmer around TZS 150,000–250,000 in labor and materials.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings
- Calculate materials required
- Select tools and materials
- Prepare materials
- Set and fix eave boards
- Fix eave covers
- Clean work place and tools
- Store tools in a safe place
Tathmini ya matokeo
Constructed eave conform to technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The students should be able to identify tools to be used and state procedures of Constructing open eave
Principles: The student should be able to explain principles related to constructing open eave
Theories: The students should be able to explain importance of open eave
Circumstantial knowledge: Workshop safety
Swali
What are open eaves in roof construction?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado