Mada za sehemu hiiConstructing eaves and bargeboardMada 5
- Constructing open eaves
- Constructing closed eaves
- Constructing flush eaves
- Constructing sprocket eaves
- Fixing fascia board
A closed eave is a roof eave where the space between the rafters is enclosed with a soffit board, giving the roof a finished appearance and preventing the entry of birds, insects, and other pests into the roof cavity.
Closed eaves serve several important functions in building construction:
- Provide a neat and attractive appearance to the roofline
- Protect the roof space from weather elements such as rain and wind
- Prevent birds, bats, and insects from nesting in the roof
- Improve thermal insulation of the building
- Create a clean junction between the wall and the roof
The main parts that make up a closed eave assembly include:
- Fascia board – a horizontal board fixed to the ends of the rafters, to which the gutter is attached
- Soffit board – the horizontal or sloped board that closes the gap under the rafters
- Rafter ends – the exposed ends of the rafters that project beyond the wall plate
- Battens – thin wooden strips used to fix the soffit board to the rafters
- Wall plate – a horizontal timber member laid on the wall top to receive the rafters
The following tools are needed for constructing closed eaves:
- Try square
- Tape measure
- Sliding bevel
- Hand saw
- Claw hammer
- Claw bar
- Mallet hammer
- Chisels
- Manila line
- Spirit level
- Ladder
- Pencil
Safety gear that must be worn:
- Safety boots
- Safety helmet
- Overall
Step 1: Prepare the Rafter Ends
Before fixing any components, ensure all rafter ends are cut to the correct line and are level. Use a spirit level to check that all rafter ends are in alignment. The rafter ends should project beyond the wall by the required eave width (typically 450mm to 600mm for most buildings in Tanzania).
Step 2: Fix the Fascia Board
- Measure and mark the required length of the fascia board using a tape measure
- Cut the fascia board to size with a hand saw, ensuring square ends
- Position the fascia board against the rafter ends, flush with their bottoms
- Nail the fascia board to each rafter end using clasp nails or wire nails, typically 75mm long
- Check alignment with a spirit level as you proceed
Step 3: Fix the Soffit Board
- Measure the distance from the wall to the fascia board to determine the soffit width
- Cut the soffit board to the required width, allowing for any necessary joints
- Position the soffit board flush against the wall and under the fascia board
- Fix battens to the rafters to provide a fixing point for the soffit
- Nail the soffit board to the battens using galvanised nails, typically 40mm long
- Ensure joints between soffit boards fall on rafters or battens for support
Step 4: Check and Finish
- Verify all components are level and properly aligned
- Ensure all nails are properly fixed and flush with the wood surface
- Apply wood preservative to any cut ends to prevent decay
A classroom building in Arusha has rafters spaced at 450mm centres. The eave projection required is 500mm, and the wall thickness is 230mm (one brick wall). Calculate the length of fascia board needed for one side of the building that is 9 metres long.
Solution:
- Total length of fascia board = 9 metres (9000mm)
- Number of rafters = (9000 ÷ 450) + 1 = 20 + 1 = 21 rafters
- This is sufficient for one continuous fascia board, assuming no joints are required
- Therefore, the fascia board length required is 9 metres
In practice, the carpenter would add approximately 50mm to each end for trimming, so the fascia board would be cut to 9100mm.
- Always wear safety boots, helmet, and overall when working at heights
- Ensure the ladder is properly secured before climbing
- Use a claw bar carefully when removing nails to avoid injury
- Keep tools in good condition and use them only for their intended purpose
- Work with a partner when handling long boards
- Check for overhead power lines before positioning the ladder
In Tanzania, constructing closed eaves is a skill directly applied when building houses in rural and urban areas. For example, a carpenter in Mwanza contracted to construct a two-bedroom house would need to properly install closed eaves to prevent bats and birds from entering the roof space, which is particularly important in areas near lakes where pests are common. A properly constructed closed eave also helps reduce maintenance costs for homeowners by protecting the roof structure from weather damage and pest infestation, making the building more durable in the long run.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings
- Calculate materials required
- Select tools and materials
- Prepare materials
- Set and fix eave boards
- Fix eave covers
- Clean work place and tools
- Store tools in a safe place
Tathmini ya matokeo
Closed eave conform to technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The students should be able to identify tools to be used and state procedures of constructing closed eave
Principles: The student should be able to explain principles related to constructing closed eave
Theories: The students should be able to explain importance of closed eave
Circumstantial knowledge: Workshop safety
Swali
What is the main purpose of constructing closed eaves in a building?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado