Mada za sehemu hiiConstructing timber stairsMada 3
- Constructing straight flight stair
- Constructing quarter turn stair
- Constructing half turn stair
Constructing a Quarter Turn Stair
A quarter turn stair is a type of staircase that makes a 90-degree turn at a landing or by means of winders. This design is commonly used in Tanzanian buildings where space is limited, such as in residential homes, offices, and public buildings. The quarter turn allows the staircase to change direction while occupying less floor space compared to a straight flight.
Before constructing a quarter turn stair, you must understand its main parts:
-
Tread: The horizontal part of the step where you place your foot. Standard residential treads are 250mm to 300mm wide.
-
Riser: The vertical part of the step connecting two treads. Standard riser height is 150mm to 190mm.
-
Stringer (or String): The inclined board that supports the treads and risers. There are two types:
- Cut stringer: Notches are cut to receive treads and risers
- Closed stringer: Treads and risers are housed into the stringer
-
Newel post: The vertical post at the start, end, and turn of the staircase that provides support to the handrail.
-
Landing: The flat platform where the stair turns 90 degrees.
-
Winder steps: Triangular treads used to turn the stairs without a landing (optional).
-
Handrail: The horizontal or inclined rail fixed above the newel posts for support.
When designing a quarter turn stair for a specific location, consider the following:
-
Total rise: Measure the vertical height from floor to floor. This determines the number of risers needed.
-
Total run: Measure the horizontal length available for the staircase.
-
Going (tread depth): The horizontal depth of each tread should be at least 250mm for comfortable use.
-
Riser height: Should be between 150mm and 190mm. All risers must be equal in height for safety.
-
Clear width: The minimum width for a domestic staircase is 900mm.
The relationship between riser and going must follow the " Blondel Formula":
2×Riser height+Going=600mm to 650mm
Where Riser height is in mm and Going is in mm.
A classroom in Arusha needs a quarter turn stair to connect two levels with a total rise of 2400mm. Calculate the number of risers and the individual riser height if you use 12 risers.
Solution:
- Number of risers = 12
- Total rise = 2400mm
Individual riser height=Number of risersTotal rise=122400mm=200mm
Since 200mm is within the acceptable range (150-190mm may be preferred, but 200mm is workable), this design is acceptable. The going (tread depth) should then be calculated using the Blondel formula:
Going=650mm−(2×200mm)=650mm−400mm=250mm
Therefore, each tread should have a going of 250mm.
Step 1: Take Accurate Measurements
Use a tape measure to determine:
- Total floor-to-floor rise
- Available floor space (total run)
- Width of the staircase
Record all measurements clearly on a working drawing.
Step 2: Calculate the Rise and Going
Divide the total rise by the desired riser height to find the number of risers. Adjust to ensure equal riser heights. Then calculate the going using the Blondel formula.
Step 3: Mark Out the Stringers
- Set out the stringer on a 50mm x 200mm timber plank.
- Use a try square to mark the riser heights along the vertical edge.
- Mark the going (tread width) along the horizontal edge.
- Draw the notches for each step using a carpenter's pencil.
- Number each step in sequence.
Step 4: Cut the Stringers
- Use a hand saw to cut along the marked lines.
- Cut the notches cleanly to ensure accurate fitting.
- Sand any rough edges with a bench plane.
Step 5: Install the Stringers
- Position the stringers at the correct spacing (usually 900mm apart for domestic stairs).
- Use cramps to hold them in place while checking with a spirit level.
- Secure the stringers to the wall using appropriate fixings.
- Ensure they are perfectly vertical and parallel.
Step 6: Fit the Treads and Risers
- Cut treads to size from 25mm thick timber.
- Cut risers from 19mm thick timber.
- Fit treads into the notches or onto the stringers.
- Fit risers above the treads, ensuring tight joints.
- Use a mallet hammer and wooden block to tap pieces into position if needed.
- Secure with nails or screws.
Step 7: Install the Landing
If using a quarter turn with a landing:
- Construct a framed platform at the turn point.
- Ensure it is level using a spirit level.
- Support with suitable framing timber.
Step 8: Install Newel Posts and Handrail
- Cut newel posts to the correct height at the start, turn, and end of the stair.
- Secure posts to the stringers and landing using dowels or screws.
- Cut and fit the handrail to follow the pitch of the stairs.
- Secure the handrail to the newel posts.
Step 9: Finishing
- Check all joints are tight and secure.
- Fill any gaps or nail holes with wood filler.
- Sand all surfaces smooth.
- Apply appropriate finish (paint, varnish, or wood preservative) using a painting brush.
Always observe the following safety practices:
- Wear safety boots, overalls, and a helmet when constructing stairs.
- Use a proper ladder when working at height.
- Keep tools sharp and in good condition.
- Secure timber pieces with cramps before cutting.
- Work in well-lit areas.
- Keep the workplace clean and free of debris.
In Tanzania, quarter turn stairs are commonly constructed in many buildings including schools, offices, and homes in Dar es Salaam, Mwanza, and other cities. For example, a carpenter in Arusha might be contracted to build a quarter turn stair in a two-storey house where the ground floor is 3 meters high. Using the skills learned in this topic, the carpenter would calculate the correct number of risers and treads, cut and install the stringers, and complete the staircase with a handrail for safety. This enables efficient use of limited floor space while providing safe access between floors.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret working drawings
- Calculate materials required
- Select tools and equipment
- Set height to the first floor
- Calculate total rise and total going
- Prepare string handrail and balustrades
- Fixing rises and goings
- Apply finishes
- Clean work place
- Store tools to safe place
Tathmini ya matokeo
Quarter turn stair conforms to technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The students should be able to identify tools to be used and state procedures of constructing quarter turn stair
Principles: The student should be able to explain principles related to quarter turn stair
Theories: The students should be able to explain important aspects to consider when constructing quarter turn stair
Circumstantial knowledge: Workshop safety
Swali
What is the function of the tread in a quarter turn stair?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado