Mada za sehemu hiiConstructing formworkMada 3
- Constructing cast in-situ and pre-cast formworks
- Constructing column formwork
- Constructing beam formwork
Formwork is a temporary construction box or mould designed to hold wet concrete in place until it hardens. It gives concrete its shape and size. Without formwork, concrete structures like walls, columns, and beams would not be able to hold their shape during construction.
There are two main types of formwork used in building construction:
1. In-situ Formwork (Shuttering)
In-situ formwork is assembled on the construction site itself. This type of formwork is used for casting structural members that will become part of the building in their final position. Examples include:
- Walls
- Columns
- Suspended floors and roofs
- Steps and stairs
The concrete is poured directly into the formwork at the location where the finished structure will stand.
2. Pre-cast Formwork (Mould Boxes)
Pre-cast formwork is used when concrete units are cast in a mould either at a convenient position on site or under factory conditions. These moulds produce separate concrete units that are later transported and assembled to form the structure. Examples of products made using pre-cast formwork include:
- Building blocks
- Paving slabs
- Coping stones
- Lintels
- Kerbstones
- Sills
- Fencing poles
- Beams
Understanding the different parts of formwork helps in constructing it correctly:
- Ties — Tensile units that connect opposite sides of formwork to resist pressure from fresh concrete
- Braces — Keep formwork upright and prevent deflection under lateral pressure
- Studs — Support sheathing panels and keep them in position
- Sheathing Panel — The surface that contacts concrete and gives it its shape
- Wales — Horizontal propping members placed against sheathing to resist pressure
- Battens — Vertical members that keep cleats and wales tight and in position
- Joists or Beams — Horizontal supports for the formwork system
- Stringers — Parallel members that align and support formwork panels
- Formwork Panels — Flat surfaces used to create slab structures
- Props or Shoring — Vertical supports that carry the formwork and concrete load
A good formwork must meet the following requirements:
- Made from cheap materials to minimize cost
- Waterproof so it does not absorb water from concrete
- Able to withstand all loads imposed on it (weight of wet concrete, workers, equipment)
- As light as possible for easy handling
- Strong and durable
- Joints must not allow any leakage of cement paste
- Interior surface should be smooth for easy stripping (removal)
- Reusable to reduce construction costs
Step 1: Identify Materials and Tools
Materials: Timber, marine boards, releasing agent, wire nails or screws
Tools: Tape measure, pencil, hand saw, claw hammer, spirit level, building square, ladder, chisels, safety gear (gloves, goggles, helmet, safety boots)
Step 2: Plan and Design
Evaluate the construction site conditions and access dimensions. Develop a detailed design based on structural drawings. Ensure the design can support the weight of wet concrete and additional loads.
Step 3: Prepare Materials
Collect formwork panels (plywood, metal, or plastic), supports (props and braces), fasteners, and release agents. Clear and level the area where formwork will be constructed. Ensure the ground is stable.
Step 4: Construct the Formwork
For Walls:
- Erect vertical panels along the wall location
- Ensure proper alignment and plumb
- Install horizontal braces
- Secure with fasteners and tie rods
For Columns:
- Assemble column formwork panels around the column footprint
- Ensure proper alignment and vertical position
- Add internal bracing or props
- Secure panels in position
For Slabs:
- Construct a support system (shoring or scaffolding)
- Position formwork panels on the support framework
- Ensure they are level and aligned
- Add supports and bracing
Step 5: Apply Release Agent
Before pouring concrete, apply a releasing agent on formwork surfaces. This prevents concrete from sticking and makes removal easier.
Step 6: Inspect and Verify
Check that all components are properly aligned and securely fastened. Ensure stability to support concrete weight without shifting or collapsing.
Step 7: Clean-up and Maintenance
Clean formwork components and inspect for damage. Repair or replace damaged parts before storing for future use.
Step 1: Identify Materials and Tools
Same materials and tools as in-situ formwork.
Step 2: Plan and Design
Develop detailed design based on structural drawings. Ensure design supports weight of wet concrete.
Step 3: Prepare Materials and Tools
Collect panels, supports, fasteners, and release agent. Clear and level the working area.
Step 4: Construct the Formwork
For Fencing Poles:
- Secure formwork panels with appropriate fasteners
- Use tie rods if required
- Check stability and alignment
For Kerbstones:
- Assemble formwork panels
- Ensure proper alignment
- Add internal bracing or props
- Secure in position
For Slabs:
- Build support framework
- Position formwork panels
- Ensure level and alignment
- Add supports and bracing
Step 5: Apply Release Agent
Apply release agent to surfaces before pouring concrete.
Step 6: Inspect and Verify
Check alignment and stability.
Step 7: Clean-up and Maintenance
Clean, inspect, and store components properly.
- Always wear appropriate Personal Protective Equipment (PPE): helmet, gloves, safety boots, safety goggles, overalls
- Regularly check formwork stability
- Make necessary adjustments to prevent accidents
- Ensure all personnel are properly trained
- Follow proper lifting and handling techniques
- Use ladders safely
Required Materials and Tools: Plywood, props, timber, nails, screws, screwdriver, hammer, cross-cut saw, tape measure, try square, carpenter's pencil, F-clamp, plumb bob, spirit level, release agents
Procedure:
- Wear Personal Protective Equipment (PPE)
- Select appropriate materials
- Measure and mark required length of timber
- Cut timber to required size (saw kerf should be on waste side)
- Join sides using a cleat
- Cut sides to obtain required length
- Assemble boxes
- Clean workplace and return materials and tools to correct places
In Tanzania, the skills of constructing formwork are essential for local builders and artisans who work on residential and commercial buildings. For example, when building a modern shop house (duka) in many towns like Arusha or Mwanza, a builder uses in-situ formwork to cast concrete columns and floors on site, while pre-cast formwork may be used to make concrete blocks or lintels at a workshop for later use. Understanding formwork helps a Form 2 graduate who starts as a mason or works in a hardware shop to assist customers with advice on proper construction techniques and quality building materials.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Draw formworks
- Interpret the drawings
- Calculate materials required
- Fix form work
- Level and reinforce form work
- Dismantle the form work
- Clean tools and work place
- Store tools to a safe place
Tathmini ya matokeo
Cast In-situ and Pre-cast formworks constructed as per the drawings and technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should be able to explain methods related to constructing cast In-situ and Pre-cast formworks
Principles: The student should be able to explain principles for constructing cast In-situ and Pre-cast formwork
Theories: The students should be able to explain theories related to constructing cast In-situ and Pre-cast formworks
Circumstantial knowledge: The students should explain detailed knowledge related to construct cast In-situ and Precast formwork
Swali
What is the primary purpose of formwork in concrete construction?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado