Sonzaschool
Rudi

Sekondari ya Kawaida · Kidato cha Tatu · Amali · Civil Engineering

Carpentry and Joinery With Metal Works

Erecting flying shoring

takriban dakika 4 kusoma

Majadiliano
Mada za sehemu hiiErecting shoringMada 3

Erecting Flying Shoring

Flying shoring is a temporary support system used to hold up parallel walls of two adjacent buildings when the building between them needs to be demolished or rebuilt. Without such support, the walls could collapse inward, creating a dangerous situation on a construction site.

Definition and Purpose

Flying shores are horizontal supports that temporarily stabilize parallel walls of two buildings. They are essential when:

  • An intermediate building is being demolished and rebuilt
  • Walls of adjacent buildings have become unstable due to age, settlement, or damage
  • Construction work requires removing a load-bearing wall between two structures

The shore transfers the lateral load from one wall to the other, preventing inward movement until permanent structural support is established.

Components of Flying Shore

A flying shore system consists of several key components:

  • Wall plates: Horizontal timber or steel plates fixed to both walls to distribute loads evenly
  • Needles: Steel rods or timber pieces that penetrate the wall to anchor the wall plates
  • Cleats: Short timber pieces that secure needles and prevent movement
  • Horizontal shore: The main horizontal beam that spans the gap between buildings
  • Inclined struts: Diagonal members that provide additional stability
  • Straining pieces: Components that help tension and align the system
  • Wedges: Wooden pieces used to tighten and secure connections

Types of Flying Shore

Single Flying Shore

Used when the distance between parallel walls is 9 metres or less. A single horizontal beam is positioned between two wall plates, with inclined struts providing support.

Double Flying Shore

Used when the distance between walls exceeds 9 metres. A trussed structure is employed, consisting of two horizontal shores connected by diagonal bracing to form a more rigid system capable of handling greater spans and loads.

Considerations for Erection

  • Spacing: Flying shores are typically installed at 3000 mm to 4500 mm centre-to-centre
  • Wall height: Centre lines of shores, struts, and walls should meet at floor levels
  • Single shore: Suitable for gaps up to 9 m
  • Double shore: Required for gaps greater than 9 m
  • Load assessment: Must consider wall material, height, and condition

Procedure for Erecting a Flying Shore

Step 1: Inspect the buildings

Examine both buildings for cracks, stability, and load-bearing capacity. Identify any existing damage that may affect the shoring installation.

Step 2: Measure and plan

Measure the exact distance between the buildings. Determine the optimal height for shore placement. Calculate the number of flying shores required based on spacing (3–4.5 m apart).

Step 3: Install wall plates

Mark identical heights on both buildings. For masonry walls, drill 22 mm diameter holes through mortar joints at approximately 1.2 m intervals. Insert steel needles into the holes. Secure 150 mm × 150 mm wall plates to the needles using M16 bolts. Ensure plates are level and aligned on both sides.

Step 4: Position the horizontal shore

Cut timber beams to span the gap between buildings. Using appropriate lifting methods, place the main shore between the two wall plates. Secure it tightly using wedges or screw jacks at both ends.

Step 5: Install supports and bracing

Place vertical props under the flying shore at approximately 1.5 m intervals. Ensure props are plumb (perfectly vertical) and rest on sole plates to prevent sinking. Install diagonal braces between the flying shore and props to prevent lateral movement. For long spans exceeding 9 m, use double flying shores.

Step 6: Inspect and verify

Check all timber for cracks and ensure props show no signs of buckling. Verify the main shore is free from deflection. Confirm all connections are tight and secure.

Safety Requirements

Always wear appropriate personal protective equipment (PPE) when erecting flying shores:

  • Helmet
  • Safety boots
  • Overall protective clothing
  • Leather gloves

Before starting work, inspect all tools and ensure the work area is clear of hazards.

Real-life application

In Tanzania, flying shores are commonly used during the reconstruction of old shop houses in markets such as Kariakoo in Dar es Salaam or central business districts in Arusha and Mwanza. When a building between two occupied structures needs to be rebuilt, carpenters and craftsmen erect flying shores to keep the neighboring walls stable, allowing safe demolition and reconstruction while protecting adjacent properties and the people inside them.

Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa

Tathmini ya mchakato

The student should be able to:

  • Prepare shoring members
  • Calculate materials required
  • Set /prepare shoring
  • Erect shoring
  • Reinforce shores
  • Dismantle shores
  • Clean work area and tools
  • Store tools at a safe place

Tathmini ya matokeo

Constructed flying shores conform to technical specifications

Tathmini ya maarifa

Detailed knowledge of:

Method used: The student should explain methods related to erecting flying shoring

Principles: The student should explain principles related to erecting flying shoring

Theories: The students should explain theories related to erecting flying shoring

Circumstantial knowledge: The students should explain detailed knowledge related to erecting flying shoring

Swali

What is the primary purpose of flying shores in construction?

Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.

Ingia ili kufanya mazoezi

Mwalimu

Umekwama? Niulize chochote kuhusu mada hii.

Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.

Ingia ili kuuliza

Majadiliano

Hakuna maswali bado

Ingia ili kuuliza
Inapakia majadiliano…