Mada za sehemu hiiErecting shoringMada 3
- Erecting racking shoring
- Erecting flying shoring
- Erecting dead shoring
A raking shore, also called an inclined shore, is a temporary support system used in construction to stabilize leaning walls, unsafe structures, or adjacent buildings during repairs, demolition, or excavation. It transfers the lateral load from a leaning or weakened wall to the ground through inclined members called rakers.
A raking shore consists of several interconnected parts that work together to provide stable support:
Wall plate — a horizontal timber member fixed to the wall that collects the load being supported and spreads it across the shoring system.
Raker — the inclined member that transfers the load from the wall plate to the sole plate. It is the main structural element of the raking shore.
Sole plate — a horizontal base placed on the ground that receives the load from the raker and distributes it to the earth.
Top cleat — a short piece of timber (approximately 2 feet) nailed to the top of the wall plate to prevent the raker from sliding upward.
Bottom cleat — a short piece of timber nailed to the top of the sole plate to prevent the raker from sliding backward.
Wedges — wooden inclined planes placed between the raker and bottom cleat to allow fine adjustment of the shore.
Gusset plates — plywood sheets nailed to both sides of connections (wall plate, sole plate, and raker ends) to prevent dislodgment.
Mid-point braces — horizontal or diagonal members fixed along the raker to reduce its effective length and increase strength.
Bottom braces — pieces of timber connecting the base of the raker to the wall plate for additional stability.
Horizontal braces — members connecting multiple raker shores near the top and bottom for lateral stability.
X and V braces — diagonal members arranged in an X or V pattern between rakers to resist lateral movement.
When installing a raking shore, the following requirements must be met:
- Angle of inclination: Rakers must be inclined at an angle between 45° and 75° from the ground. The optimal angle is 60°.
- Spacing: Raking shores should be positioned at intervals of 3 to 4.5 metres along the wall.
- Sole plate: The sole plate must be embedded into the ground and rest on a firm, level base.
- Rider raker: For tall buildings, a rider raker may be introduced to reduce the length of the main raker.
The length of a raker depends on the wall height and the chosen inclination angle. The formula is:
Raker length=sinθWall height
Where θ is the angle of inclination.
Example: A brick wall is 3 metres high and leans outward. Calculate the raker length if the inclination angle is 60°.
Solution:
Raker length=sin60°3=0.8663=3.46 m
Therefore, a raker approximately 3.5 metres long is required.
-
Measure the wall — Determine the wall's lean angle using a protractor. The target angle should range from 45° to 75°.
-
Calculate raker length — Use the formula: raker length = wall height ÷ sin(angle).
-
Install wall plate — Fix a horizontal wall plate to the wall at 1.2-metre height intervals. Secure it with steel needles drilled into mortar joints for heavy walls.
-
Prepare the base — Compact the soil and lay a timber sole plate on concrete blocks. Ensure the base is level and stable.
-
Cut and position rakers — Cut timber beams to the calculated lengths. Install rakers at the selected angle between the wall plate and the sole plate. Use wedges for fastening.
-
Install braces — Add diagonal braces between rakers in an X pattern. Nail all connections tightly.
-
Test stability — Apply gentle pressure to check for movement and stability before starting repair work.
-
Observe safety — Wear appropriate PPE including helmet, safety boots, overall, and leather gloves throughout the activity.
-
Clean the working area — Store tools properly after completion.
- Always wear personal protective equipment (helmet, safety boots, overall, leather gloves)
- Ensure the sole plate is on firm, compacted ground to prevent sinking
- Check all connections are tight before leaving the site
- Never work under an unstable wall without proper shoring in place
- Inspect the shoring daily for any signs of movement or failure
In Tanzania, raking shores are commonly used when repairing old buildings in areas like Kigamboni or during the renovation of traditional Swahili houses in Stone Town, Zanzibar, where walls may have tilted due to foundation settlement. A local artisan or fundi majumba would use timber rakers to temporarily support such walls before rebuilding or strengthening the foundation, ensuring the safety of workers and preventing collapse during construction.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Prepare shoring members
- Calculate materials required
- Set /prepare shoring
- Erect shoring
- Reinforce shores
- Dismantle shores
- Clean work area and tools
- Store tools at a safe place
Tathmini ya matokeo
Constructed racking shores conform to technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should explain methods related to erecting racking shoring
Principles: The student should explain principles related to erecting racking shoring
Theories: The students should explain theories related to erecting racking shoring
Circumstantial knowledge: The students should explain detailed knowledge related to erecting racking shoring
Swali
What is the main function of a bottom cleat in a raking shore system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado