Mada za sehemu hiiConstructing shutteringMada 3
- Constructing balcony shuttering
- Constructing upper floor shuttering
- Constructing stair shuttering
Constructing Stair Shutter
A staircase is a structural element that provides access between different floor levels in a building. It consists of a series of steps that allow people to move from one floor to another. In construction, stair shuttering is the temporary formwork mould used to shape concrete stairs until the concrete hardens and can support itself. This study note explains the key parts of stairs, types of staircases, and the step-by-step procedure for constructing stair shuttering.
Understanding the terminology of stair parts is essential for accurate construction. The main components are:
- Step: A step is the combination of a tread and a riser, forming one complete level of the staircase.
- Tread: The tread is the horizontal upper surface of the step where the foot is placed when ascending or descending.
- Riser: The riser is the vertical portion of the step connecting one tread to the next.
- Rise: The rise is the vertical distance or height between two consecutive treads.
- Going: The going is the horizontal distance between two adjacent risers.
- Flight: A flight is a continuous series of steps without any break, extending from one landing to the next.
- Landing: A landing is a horizontal platform between two successive flights, providing a rest point.
- Stairway: The stairway is the opening or space occupied by the stairs.
- Stairwell: The stairwell is a vertical compartment extending through a building in which stairs are placed.
- Headroom: Headroom is the vertical distance between the tread of one flight and the ceiling above.
- Handrail: An inclined or horizontal rail provided above the balusters for support.
- Pitch: The pitch is the vertical angle made by the nosing line of the stair with the horizontal.
Stairs are classified according to their arrangement and the direction of travel:
Straight Flight Stairs
This is the simplest form of staircase, having no change in direction between two successive floors. It consists of a single run of steps in a straight line. Such stairs are suitable for small houses where long and narrow spaces are available.
Turning Stairs
These stairs change direction as you go up, with or without a landing. They include:
- Quarter-turn stairs: Have one landing and one turn, used when space for a straight flight is limited.
- Half-turn stairs: Have two turns, typically with a landing at the mid-point.
- Bifurcated stairs: Branch into two flights at a landing.
Continuous Stairs
This type combines more than one straight flight with intermediate landings between them, common in multi-storey buildings.
The table below provides general design guidelines for comfortable and safe stairs:
| Type of Building | Rise (R) | Tread (T) | T + 2R (Comfort Formula) | Stair Width |
|---|---|---|---|---|
| Residential Building | 150 mm to 180 mm | 225 mm to 275 mm | 500 mm to 650 mm | 0.8 m to 1.0 m |
| Public Building | 120 mm to 150 mm | 250 mm to 300 mm | 500 mm to 650 mm | 1.8 m to 2.0 m |
The comfort formula T + 2R ensures that the relationship between tread and riser produces comfortable stepping. A value between 500 mm and 650 mm generally provides good ergonomics.
Materials
- Plywood sheets (18–25 mm thick) for treads and risers
- Wooden planks (50 mm × 100 mm) for stringers
- Wooden planks (50 mm × 50 mm) for bracing
- Props for supporting the formwork
- Nails and screws for fixing components
- Reinforcement bars (to be placed by steel fixers)
Tools and Equipment
- Tape measure
- Spirit level
- Plumb bob
- Framing square or carpenter's square
- Chalk line
- Hand saw or circular saw
- Jigsaw (for cutting curves)
- Chisel and hammer
- Safety equipment (helmet, gloves, safety boots, goggles)
Follow these systematic steps to construct stair shuttering:
Step 1: Study the Drawings
Review architectural and structural drawings to confirm:
- Total rise (total vertical height)
- Number of steps
- Tread width
- Riser height
- Landing positions
Step 2: Mark Reference Lines
Use a chalk line to mark reference lines on walls and floor. Outline the positions of treads, risers, and landings. Verify that the total rise matches the design specification.
Example: For a staircase with a total rise of 3.3 m and 22 steps, the height of each riser equals 3,300 mm ÷ 22 = 150 mm.
Step 3: Cut and Install Side Stringers
Side stringers are the inclined side supports that carry the weight of the stairs. Cut wooden planks to match the stair angle and notch them to receive the treads and risers. Fix the stringers vertically to the walls and tighten them with horizontal struts. Check alignment using a spirit level.
Step 4: Sheath the Landing and Waist
Cut plywood or marine board and cover the landing and waist areas on the installed stringers. Place props beneath the sheathing to provide adequate support.
Step 5: Lay Reinforcement
Install reinforcement bars as per the structural design and tie them securely. This work is normally done by steel fixers.
Step 6: Install Riser Shutters
Nail vertical plywood pieces between the stringers at each step position. Secure them with horizontal braces to prevent sideways bulging. Ensure risers are vertical and treads are horizontal.
Step 7: Strengthen the Formwork
Add diagonal braces between stringers and props for stability. Verify that all treads are level, risers are uniform in height, and no gaps exist in the formwork that could cause concrete leakage.
Step 8: Final Inspection
Before pouring concrete, check:
- All treads are level using a spirit level
- All risers are uniform in height
- No gaps greater than 2 mm at joints
- Props are firmly secured
- Formwork is properly aligned according to drawings
A reinforced concrete staircase has the following specifications:
- Total rise: 3.3 m
- Number of steps: 22
- Tread width: 300 mm
- Riser height: 150 mm
- Stair width: 2.5 m
(a) Calculate Total Horizontal Run
The total horizontal run (going) equals the number of treads multiplied by the tread width. For 22 steps, there are 21 treads (the top landing is not counted as a tread).
Total run=21×300 mm=6,300 mm=6.3 m
(b) Calculate Angle of Inclination
The pitch or angle of inclination is calculated using the tangent formula:
tanθ=total runtotal rise=6.33.3=0.5238
θ=tan−1(0.5238)≈27.6∘
(c) Quantity of Materials for Shuttering
For plywood sheets (18–25 mm thick):
- Area of treads: 21 treads × 2.5 m width × 0.3 m = 15.75 m²
- Area of risers: 22 risers × 2.5 m width × 0.15 m = 8.25 m²
- Total plywood area: approximately 24 m² (adding 10% for waste)
For wooden planks (50 × 100 mm for stringers and bracing):
- Two stringers at 7 m each = 14 m of 50 × 100 mm timber
- Additional bracing timber: approximately 20 m of 50 × 50 mm
When constructing stair shuttering, always observe the following safety measures:
- Wear appropriate PPE: safety helmet, safety boots, gloves, safety goggles, and overalls
- Ensure the working area is clean and free of debris
- Check that all props are firmly secured on the ground
- Verify that the formwork is properly braced before concreting
- Never work on unstable or improperly supported formwork
- Use ladders safely when working at height
| Problem | Likely Cause | Solution |
|---|---|---|
| Formwork shifts during concreting | Insufficient bracing or loose props | Add diagonal braces and secure props with wedges |
| Tread not level | Incorrect positioning or loose stringer | Adjust stringer position and check with spirit level |
| Uneven riser heights | Measurement error in marking | Remove and re-fix the riser shutter at correct height |
| Concrete leakage through joints | Gaps in formwork | Seal gaps with tape or timber strips before pouring |
In Tanzania, stair shuttering skills are directly applied when constructing multi-storey buildings in cities like Dar es Salaam, Arusha, or Dodoma. A local artisan or fundi-mitumbao working with a small construction company would use these techniques to create concrete staircases for residential apartment buildings or commercial structures. The ability to calculate stair dimensions and construct proper shuttering enables a trained carpenter to contribute to building safe, code-compliant stairs for homes and offices across the country.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Draw balcony shuttering
- Interpret the drawings
- Calculate materials required
- Erect props for shuttering
- Fix shuttering
- Level and reinforce form work
- Dismantle the shuttering
- Clean tools and work place
- Store tools to a safe place
Tathmini ya matokeo
Constructed stair shuttering conforms to drawing and technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should explain methods related to constructing stair shuttering
Principles: The student should explain principles related to constructing stair shuttering
Theories: The students should explain theories related to constructing stair shuttering
Circumstantial knowledge: The students should explain detailed knowledge related to constructing stair shuttering
Swali
What is the "going" of a staircase?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado