Mada za sehemu hiiCarrying out system earthingMada 4
- Performing TT earthing methods
- Performing IT earthing method
- Performing TN-S earthing method
- Performing bonding of metal fixtures
TT Earthing Method
TT earthing is a method of connecting the metal parts of an electrical installation to the earth. In the TT system, the consumer provides their own earth electrode (ground rod) at the building, separate from the earth electrode provided by the supply authority at the transformer. This method is commonly used in rural areas where electricity comes from overhead power lines.
TT stands for Terra-Terra, which means "Earth-Earth." In this system:
- The first "T" shows that the supply authority's transformer is connected to earth at its own electrode.
- The second "T" shows that the consumer also has their own earth electrode at the premises.
The two earth electrodes are independent of each other. When a fault occurs, the fault current flows through the consumer's earth electrode into the ground and back to the supply authority's earth electrode.
- Earth electrode (Ground rod): A metal rod driven into the ground to make contact with soil
- Earth continuity conductor: A green-and-yellow coloured wire that connects electrical equipment to the earth electrode
- Earth resistance: The resistance of the soil between the electrode and true earth; should be as low as possible (below 10 ohms for most installations)
Step 1: Gather Tools and Safety Equipment
Before starting, collect: spanners, screwdrivers, hoe, spade, clamp on meter, ground resistance meter, safety boots, safety goggles, plastic gloves, and overalls.
Step 2: Select the Location
Choose a spot for the earth electrode that is:
- At least 1.5 meters away from the building foundation
- Near the main switch or distribution board
- In damp soil if possible (dry soil has high resistance)
- Away from underground pipes or cables
Step 3: Prepare the Earth Electrode
Use a copper-coated steel rod or galvanized pipe, at least 2.5 meters long and 15mm in diameter. Dig a hole about 0.5 meters deep at the selected location.
Step 4: Install the Earth Electrode
Drive the earth rod vertically into the ground until only about 15cm remains above the surface. If the soil is hard, use a hammer or driving tool.
Step 5: Connect the Earth Continuity Conductor
Using a suitable clamp or connector, attach the green-and-yellow earth wire from the main switch to the earth electrode. Tighten all connections securely with spanners and screwdrivers.
Step 6: Test the Earth Resistance
Use a ground resistance meter to measure the earth resistance. Connect the meter according to the manufacturer's instructions and read the value. The reading should be below 10 ohms. If the reading is too high, you may need to:
- Drive the electrode deeper
- Add more earth rods in parallel
- Pour water around the electrode to moisten the soil
Step 7: Record the Results
Write down the measured earth resistance value and the date of testing. Keep this record for future reference.
- Always wear safety boots, goggles, gloves, and overalls during installation
- Ensure the power supply is switched off before working on earthing
- Check for underground services before digging
- Never use a damaged or corroded earth electrode
- Make sure all connections are tight and secure
A school in a rural village in Mbeya needs to install TT earthing. The electrician selects a damp location near the main switch. After driving a 2.5m earth rod, the ground resistance meter reads 25 ohms. This is too high because the standard requires less than 10 ohms.
Solution: The electrician adds a second earth rod 1.5 meters away from the first one and connects them in parallel. The combined resistance is calculated as:
Rtotal=R1+R2R1×R2
If both rods give 25 ohms:
Rtotal=25+2525×25=50625=12.5Ω
The resistance is still high, so the electrician pours water around both rods to moisten the soil. The reading drops to 8 ohms, which is now acceptable.
In Tanzania, TT earthing is commonly used in many homes and schools in rural areas like Singida, Shinyanga, and many villages where electricity is supplied through overhead lines. A small shop owner in Morogoro who installs a new electric cooker or water heater must ensure proper TT earthing is done to protect their family and customers from electric shocks. Without proper earthing, a fault in the appliance could make the metal casing live and dangerous to touch.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to: Select tools, equipment, and safety gear.
- Draw electrical TT earthing system diagrams.
- Identify the earthing electrodes.
- Install the TT earthing system.
- Test the function of the TT earthing system.
- Observe safety precautions.
- Clean the workplace, tools, and equipment.
Tathmini ya matokeo
Acceptable TT earthing systems installed as per I.E.E. regulations.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to install the TT earthing system.
Principles: The student should explain the principles of performing earthing methods.
Theories: The student should explain:
- Electrical symbols used in the earthing system.
- The terms “earthing, bonding, and grounding.”
- The earth electrode.
- The earth fault loop impedance.
- The meaning of TT, IT, and TN systems.
- The application of TT, IT, and TN systems.
- Earth leakage.
Detailed knowledge about:
- TT earthing systems.
Swali
What does the abbreviation "TT" stand for in TT earthing?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado