Mada za sehemu hiiCarrying out system earthingMada 4
- Performing TT earthing methods
- Performing IT earthing method
- Performing TN-S earthing method
- Performing bonding of metal fixtures
Bonding of Metal Fixtures in Electrical Installation
Bonding is the process of connecting all exposed metal parts of an electrical installation together using conductors. This creates a low-resistance path that ensures all metal fixtures are at the same electrical potential, preventing dangerous voltage differences that could cause electric shocks.
In simple terms, bonding connects metal items like switch plates, light fitting housings, metal conduits, and distribution boxes so that if a fault occurs, electricity flows safely through the bonding conductor instead of through a person who touches the metal.
- Prevents electric shock — If a live wire touches a metal fixture, the metal becomes dangerous. Bonding ensures the fault current flows to earth, tripping the protective device.
- Reduces fire risk — Fault currents can cause overheating. Bonding allows quick disconnection by protective devices.
- Ensures safety — All bonded metal parts remain at equal voltage, eliminating dangerous potential differences.
Main Bonding
Main bonding connects the main earthing terminal to all major metal parts of the building, including:
- Water pipes
- Gas pipes
- Structural steel
- Central heating systems
Supplementary Bonding
Supplementary bonding connects metal parts that can be touched simultaneously, such as:
- Metal bath or shower units
- Radiators
- Kitchen appliances
- Light switches and socket faceplates
Step 1: Identify Metal Fixtures
Walk through the installation and list all metal parts that need bonding:
- Switch plates and socket outlets (metal faceplates)
- Light fitting housings
- Metal conduit and trunking
- Distribution boards
- Water and gas pipes entering the building
Step 2: Select Proper Bonding Conductors
- Use appropriate size bonding conductors (typically 4mm² or 6mm² copper)
- Ensure conductors are identified with green-and-yellow sleeve or tape
- Use suitable connectors and clamps
Step 3: Make Secure Connections
- Clean metal surfaces to remove paint, rust, or grease
- Use approved earth clamps or bolts with washers
- Tighten all connections properly using spanners
- Ensure mechanical strength and good electrical contact
Step 4: Test the Bonding
After installation, verify:
- Continuity test using a multimeter or megger
- All connections are secure and low resistance
- The resistance of the bonding conductor does not exceed 0.5 ohms
When performing bonding, always wear:
- Safety boots
- Safety goggles
- Plastic gloves
- Overalls
Use insulated tools and ensure the power supply is switched off before working on any electrical installation.
A school workshop in Dar es Salaam has a new metal Distribution Board (DB). The DB is mounted on a metal frame, and there are three metal conduits running from it to the workshop walls.
Procedure:
- Identify metal parts: DB casing, metal frame, three metal conduits
- Select 6mm² copper bonding conductors with green-and-yellow identification
- Connect bonding conductor from DB casing to metal frame using an earth clamp
- Connect each metal conduit to the main earthing terminal using earth clamps
- Test continuity between all bonded parts — the resistance should be less than 0.5 ohms
The bonding ensures that if a live conductor inside the DB becomes loose and touches the metal casing, the fault current flows through the bonding conductor to earth, causing the circuit breaker to trip immediately and protecting anyone who might touch the metal parts.
In many Tanzanian homes and businesses, metal switch plates, socket outlets, and light fittings are installed. When a fault occurs, such as a live wire touching the metal plate, bonding ensures the metal does not become dangerous. A student trained in bonding procedures can safely install or maintain these fixtures in their family's house or in small electrical contracting jobs common in local communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment, and safety gear.
- Draw electrical bonding of metal fixtures.
- Observe safety precautions.
- Clean the workplace, tools, and equipment.
Tathmini ya matokeo
Acceptable bonding of metal fixtures installed as per I.E.E. regulations.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to perform bonding of metal fixtures.
Principles: The student should explain the principles of performing bonding of metal fixtures.
Theories: The student should explain:
- Electrical symbols used in the earthing system.
- The terms “bonding.”
- The earth electrode. The meaning of bonding of metal fixtures.
- The application of bonding of metal fixtures.
- The earth fault
Detailed knowledge about:
- Bonding of metal fixtures.
Swali
What is the primary purpose of bonding metal fixtures in an electrical installation?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado