Mada za sehemu hiiCarrying out system earthingMada 4
- Performing TT earthing methods
- Performing IT earthing method
- Performing TN-S earthing method
- Performing bonding of metal fixtures
IT Earthing Method
IT earthing is a special type of system earthing where the electrical supply source (such as a transformer) has no direct connection to earth, and the consumer's earth electrode is completely separate from the supply system. The letters "IT" come from the French term Isolation Terre, meaning "insulated earth."
In this system:
- The supply side (the transformer's neutral point) is isolated from earth or connected through a high resistance
- The consumer's installation has its own dedicated earth electrode that is separate from the supply system's earth
- When a single fault occurs (such as a live wire touching the earth), no dangerous fault current flows through the earth, so the system can continue operating safely
The main reasons for using IT earthing include:
- Continuity of supply – The system can continue operating even when a fault to earth occurs
- Safety – No dangerous touch voltages appear on exposed metal parts during the first fault
- Reduced maintenance downtime – Critical systems (like hospitals and industrial processes) can keep running until maintenance is convenient
- Fire prevention – Since no large earth fault current flows, the risk of sparking and fire is reduced
| Term | Meaning |
|---|---|
| Isolated supply | Power source with no direct connection to earth |
| Earth electrode | Conductor buried in the ground that provides a connection to earth |
| First fault | The first occurrence of a line-to-earth fault in an IT system |
| Touch voltage | Voltage that a person could experience when touching exposed metal parts |
The following tools and safety gear are needed to perform IT earthing:
- Measuring instruments: Clamp on meter, Megger meter, Ground resistance meter
- Hand tools: Set of spanners, Set of screwdrivers, Hoe, Spade
- Safety gear: Safety boots, Safety goggles, Plastic gloves, Overalls
Step 1: Plan the installation
- Identify the location for the earth electrode, preferably in moist soil away from buried services
- Ensure the consumer earth electrode is completely separate from any supply system earth
Step 2: Excavate the earth pit
- Dig a hole or trench at the chosen location using a hoe and spade
- The pit should be at least 0.5 meters deep, or as specified in local standards
Step 3: Install the earth electrode
- Drive the earth electrode (earth rod or plate) into the ground at the bottom of the pit
- Ensure good contact with the surrounding soil
Step 4: Connect the earth conductor
- Run the earth conductor from the consumer's main earthing bar to the earth electrode
- Use proper clamps and connections to ensure a tight, corrosion-resistant joint
Step 5: Test the earth resistance
- Use a megger meter or ground resistance meter to measure the earth resistance
- The resistance should be low enough to ensure proper operation (typically below 10 ohms for consumer installations)
- If the reading is too high, improve the earth by adding more electrodes or treating the soil
Step 6: Backfill the pit
- Fill the pit with moist soil, compacting it carefully around the electrode
- Ensure the soil remains moist for good electrical contact
- Always wear safety boots, goggles, gloves, and overalls during installation
- Ensure the power supply is switched off before working on earthing connections
- Check for buried services (water pipes, cables) before digging
- Use insulated tools for electrical work
- After installation, verify all connections are secure and protected from corrosion
A small clinic in Mwanza requires an IT earthing system for its emergency power supply. The electrician installs a separate earth electrode for the generator system, ensuring it is at least 10 meters away from the main building's earth electrode. After driving the earth rod and connecting the earth conductor, the electrician uses a ground resistance meter and obtains a reading of 8 ohms.
Question: Is this reading acceptable?
Answer: Yes. The reading of 8 ohms is below the typical maximum of 10 ohms for consumer installations, so the IT earthing system is properly installed and will provide safe operation.
In Tanzania, IT earthing is commonly used in hospitals such as Bugando Medical Centre in Mwanza or Mnazi Mmoja Hospital in Zanzibar, where uninterrupted power supply is critical for life-support equipment. An electrician working at such a facility would install a separate, isolated earth system for the operating theatres to ensure that if a first fault occurs, the equipment keeps running and patients remain safe.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment, and safety gear.
- Draw electrical diagrams for IT earthing system.
- Identify the earthing electrodes.
- Install the IT earthing system.
- Test the function of the IT earthing system.
- Observe safety precautions.
- Clean the workplace, tools, and equipment.
Tathmini ya matokeo
Acceptable IT earthing systems installed as per I.E.E. regulations.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to install the IT earthing system.
Principles: The student should explain the principles of performing IT earthing methods.
Theories: The student should explain:
- Electrical symbols used in the earthing system.
- The meaning of IT, and earthing systems.
- The application of IT systems.
- Earth leakage.
- Earth fault.
Detailed knowledge about:
- IT earthing systems
Swali
What does the abbreviation "IT" stand for in the IT earthing method?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado