Mada za sehemu hiiCarrying out system earthingMada 4
- Performing TT earthing methods
- Performing IT earthing method
- Performing TN-S earthing method
- Performing bonding of metal fixtures
TN-S is a modern earthing system used in electrical installations where the neutral (N) and protective earth (PE) conductors are kept separate from the power source all the way to the consumer's installation. The letters mean:
- T – Terra (earth) – the source is directly earthed
- N – Neutral – the consumer is connected to the earthed neutral
- S – Separated – the neutral and protective earth are separate conductors
In simple terms, TN-S provides two distinct paths for electricity: one for the working current (neutral) and one for safety (protective earth). This makes it one of the safest systems for buildings.
- Earth electrode – a metal rod or plate buried in the ground that makes electrical contact with the earth
- Protective Earth (PE) conductor – a green-and-yellow coloured conductor that carries fault current safely to earth
- Neutral (N) conductor – a blue-coloured conductor that carries normal working current
- Line (L) conductor – a brown-coloured conductor that carries current from the source (live wire)
- Main earthing terminal – the point where all protective earth conductors are connected together
Step 1: Prepare Tools and Safety Gear
Before starting, gather all required tools:
- Clamp on meter
- Megger meter
- Ground resistance meter
- Spanners and screwdrivers
- Hoe and spade
- Safety boots, goggles, plastic gloves, and overalls
Always wear your safety gear before handling electrical equipment.
Step 2: Locate and Install the Earth Electrode
- Choose a location near the main distribution board, preferably in moist soil
- Use a hoe or spade to dig a hole about 0.5 metres deep
- Drive the earth electrode (metal rod) vertically into the soil
- The electrode should make good contact with the earth
Step 3: Connect the Earth Electrode to the Main Earthing Terminal
- Run a proper-sized earth conductor from the earth electrode to the main earthing terminal
- Use a clamp or connector to make a secure, tight connection
- Ensure the connection is protected from corrosion
Step 4: Install Separate N and PE Conductors
- From the supply source (substation or distribution transformer), the TN-S system provides:
- A separate neutral conductor (N)
- A separate protective earth conductor (PE)
- Run these two conductors separately through the installation
- Connect all exposed metal parts (like metal casings of appliances) to the PE conductor
Step 5: Test the Earthing System
Use the ground resistance meter to measure the earth resistance. The value should be low enough (usually below 10 ohms for safety) to allow fault current to flow safely.
A school building in Dar es Salaam needs a TN-S earthing system installed. The electrician measures the earth resistance and gets 8 ohms. Is this value acceptable?
The standard requirement is that earth resistance should be less than 10 ohms for a safe TN-S system. Since 8 ohms is less than 10 ohms, the installation is acceptable and will safely carry fault current to earth if a fault occurs.
- Always disconnect power before working on earthing installations
- Wear safety boots, gloves, and goggles at all times
- Use insulated tools
- Never touch bare conductors
- Ensure all connections are tight and corrosion-free
In Tanzania, TN-S earthing is commonly used in modern homes, schools, and hospitals. For example, when an electrician at a clinic in Arusha installs the wiring, they must connect the metal switchboard and all appliance casings to the PE conductor so that if a live wire accidentally touches the metal, the fault current flows safely through the earth path rather than through a person touching the equipment.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools, equipment, and safety gear.
- Draw electrical for TN-S earthing system diagrams.
- Identify the earthing electrodes.
- Install the TN-S earthing system.
- Test the function of the TN-S earthing system.
- Observe safety precautions
- Clean the workplace, tools, and equipment.
Tathmini ya matokeo
Acceptable TN-S earthing systems installed as per I.E.E. regulations.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to install the TN-S earthing system.
Principles: The student should explain the principles of performing TN-S earthing methods
Theories: The student should explain:
- Electrical symbols used in the earthing system.
- The meaning of TN-S systems.
- The application of TN_S systems.
- Earth leakage.
- Earth fault
Detailed knowledge about:
- TN-S earthing systems.
Swali
What does the letter S stand for in TN-S earthing system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado