Mada za sehemu hiiPreserving raw hides and skinsMada 5
After flaying (removing the hide from the animal), the raw hide or skin still has unwanted tissues attached. Removing these remnants is a critical step before preservation and tanning, because any remaining flesh, fat, or connective tissue will cause the hide to rot and make it unusable for leather production.
Remnants are the unwanted parts of a raw hide or skin that must be removed before processing. They include:
- Flesh and fat stuck to the inner side of the hide
- Sinews and membranes connecting tissue layers
- Ears, tails, and hooves that were not cut off during flaying
- Blood clots and dirt that remain on the surface
If remnants are not properly removed, bacteria will grow on them and the hide will decay, making it worthless for leather making.
Long before leather factories existed, rural communities preserved hides by drying them and tanned them with local materials such as tree bark. This small-scale work is still called rural tanning. Raw hides (from large animals such as cattle) and skins (from small animals such as goats and sheep) are used to make leather for shoes, sandals, belts and bags, and also drum heads, ropes, straps and glue.
Before starting, spread the hide out and look at both sides. Common defects are:
- Flay cuts and holes made by careless knife work during flaying
- Brand marks burnt into the living animal to show ownership. A brand on the back or rump spoils the best part of the hide, which is why livestock keepers are advised to brand low on the leg, on the neck or on the cheek
- Scratches, tick marks and scars from thorns, parasites and wounds
- Loose hair and a bad smell, which show that rotting has started
Select hides that are fresh, come from healthy animals, and have few cuts and no smell. A hide with many defects is set aside for lower-grade use.
The following tools are used for removing remnants:
- Flaying knives
- Curved panga
- Kitchen knife
- Wooden beams or tannery beams
- Hard broom
- Plastic containers
- Buckets
- Rubber gloves, safety boots, overall/dust coat, and mask for personal protection
Step 1: Secure the Hide on a Beam
Place the raw hide on a sturdy wooden beam or tannery beam. The beam should be firmly fixed to a workbench or the ground so it does not move during work. This gives you a stable surface to work on.
Step 2: Scrape Off Flesh and Fat
Using a flaying knife or curved panga, carefully scrape away all flesh and fat from the inner side of the hide. Work from the centre outward, pushing the knife away from your body. Hold the knife at a shallow angle to avoid cutting through the hide.
Step 3: Remove Sinews and Membranes
After scraping the fat, use the knife to peel off tough sinews and thin membranes still attached to the hide. These connective tissues are elastic and require a firm, pulling motion combined with cutting to separate them cleanly.
Step 4: Trim Edges
Cut off the ears, tails, and any remaining hooves using a kitchen knife or panga. Also trim ragged edges to give the hide a uniform shape, which helps with even drying and tanning later.
Step 5: Clean the Hide
Use a hard broom to brush off loose tissue, blood clots, and dirt from both sides of the hide. Rinse the hide briefly in clean water in a plastic bucket if needed, then shake off excess water.
Step 6: Inspect the Hide
Check the entire hide for any remaining remnants. Look carefully at corners and thick areas where tissue often stays attached. If you find any, remove them before proceeding to preservation.
A cleaned hide must be preserved within a few hours. The main types of preservation are:
- Air drying: the hide is stretched on a frame or hung over a pole in the shade, where moving air dries it
- Wet salting: the flesh side is covered with salt and the hides are stacked
- Dry salting: the hide is salted first and then dried
Until it is preserved, keep the hide spread out or hung in a cool, shaded, airy place, off the ground and away from dogs, insects and rain. Never leave fresh hides folded in a heap or packed in a gunny bag, because they heat up and rot.
Afterwards, wash the knives, panga, beam, broom and buckets with soap and clean water. Dry the blades and store all tools in a safe, dry place with the cutting edges covered. Put the fleshings and trimmings in a container and bury them in a pit away from houses and water sources, so that they do not attract flies and dogs. Wash your gloves, boots and hands with soap.
- Always cut away from your body to avoid injuries.
- Wear rubber gloves to protect your hands from bacteria and sharp tools.
- Use safety boots to protect your feet in case a knife slips.
- Wear a dust coat or overall and a mask to avoid inhaling bacteria and dust from the hide.
- Work only on hides from animals that were healthy when slaughtered. Never handle the hide of an animal that died of disease or of an unknown cause, because diseases such as anthrax can pass from hides to people. Report such an animal to the livestock officer.
- Cover any cut on your hands with a waterproof dressing before work. If you cut yourself, stop, wash the wound with soap and clean water, cover it and report it.
- Carry knives with the point down, never leave a knife hidden under a hide, and pass a knife to another person handle first.
A farmer in Morogoro has just slaughtered a cow and removed the hide. He notices thick fat and pieces of flesh still stuck to the inner side. He secures the hide on a tannery beam and uses a curved panga to scrape off the fat, starting from the centre and moving outward. He then trims the ears and tail, cleans the hide with a hard broom, and inspects it for any remaining remnants. The clean hide is now ready for salting and preservation.
- Remnants must be removed immediately after flaying to prevent decay.
- Always work on a stable beam and keep your cutting tools sharp.
- Safety gear is mandatory — never work without gloves and boots.
- Thorough removal of remnants produces high-quality hides suitable for good leather.
- Careful, precise knife work matters: every cut or gouge made now stays in the finished leather and lowers its value.
In many rural Tanzanian communities, families keep livestock and occasionally slaughter animals for food or sale. The hide can be processed into leather goods such as belts, sandals, or bags, providing extra income. For example, a farmer in Mwanza who properly removes remnants from a cow hide can sell the cleaned hide more easily to a local tanner, who then turns it into durable sandals sold at the market. Knowing how to remove remnants correctly ensures the hide stays intact and earns a better price.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Inspect leather defects
- Handle flaying tools and equipment
- Remove remains
- Observe safety
- Clean tools and equipment
- Store raw hides and skins
- Store tools and equipment
Tathmini ya matokeo
Raw hides and skins are clean and neat according to the required specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Handle flay knives
- Remove remains
Principles: The student should explain the principles of:
- Selecting raw hides and skins
Theories: The student should explain:
- History of rural tanning
- Branding of life stocks
- Type of preservation
- Uses of raw hides and skins
- Importance of precise and detailed work while removing remains into raw hide and skins
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions pertaining to remove remains of raw hides and skins
- Safe handling of working tools and equipment
Swali
Which of the following is a remnant that must be removed from a raw hide before it is preserved?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado