Mada za sehemu hiiPreserving raw hides and skinsMada 5
- Removing remnants
- Performing stage beams
- Washing hides and skins
- Salting raw hides and skins
- Staking raw hides and skins
Salting is the process of applying salt to raw hides and skins immediately after flaying (removing the skin from the animal) to prevent decay and bacterial attack. Raw hides and skins contain moisture and proteins that bacteria feed on, causing the material to rot and smell badly. Salt draws out moisture and creates conditions in which most bacteria cannot grow, preserving the hide until it is processed further.
Raw hides and skins spoil very quickly — within a few hours in hot weather — because they are rich in water and nutrients. If left untreated, bacteria cause:
- foul odour
- hair slippage (hair falls off the hide)
- permanent damage to the skin structure
Salting is the most common and affordable method of preserving hides and skins in rural Tanzania. It is simple, requires few materials, and can be done on the farm immediately after slaughter.
- Common salt (rock salt or sea salt) — the standard choice
- Salt should be coarse, dry and clean for best results. Do not reuse dirty salt from earlier hides: it carries salt-loving bacteria that cause red patches on the hide
A sufficient amount of salt is applied at a rate of approximately 30–40% of the weight of the raw hide or skin. This means for every kilogram of raw hide, about 300–400 grams of salt is needed. Using too little salt will not adequately preserve the hide.
-
Prepare the workspace — Set up a clean workbench or flat concrete surface. Wear protective gear: rubber gloves, overall/dust coat, safety boots, and a mask.
-
Spread the raw hide flat — Place the flayed hide flesh-side up on the work surface. Inspect it for defects such as flay cuts, holes, brand marks and patches where the hair pulls out easily (a sign that rotting has begun), and set badly damaged hides aside. Remove any excess fat, meat scraps, or blood using a flaying knife, wash off dung and dirt with clean water, and let the hide drain.
-
Apply salt generously — Take salt from the salt container and spread it evenly over the entire flesh side of the hide. Rub the salt in with the flat of a gloved hand, paying special attention to the edges, the folds and the thick parts such as the neck and backbone, which spoil first. No part of the flesh side should be left bare.
-
Stack or fold the hide — Lay the salted hide flat, flesh side up, on a raised wooden stacker that slopes slightly so that the brine runs off. Place the next hide on top, flesh side up, and salt it in the same way, building a neat pile. A single hide can instead be folded with the salted flesh side inwards.
-
Allow the hide to drain — Leave the salted hide for 24–48 hours. During this time, the salt draws most of the liquid out of the hide. Keep the pile on the sloping stacker, or hang a single hide over a tannery beam or water horse, so that the brine drains away into a bucket and does not soak back into the hide.
-
Re-salt if necessary — After the first draining, shake off the wet salt and apply fresh salt wherever the flesh side shows bare patches; thick hides usually need this second salting. Stack again. Curing is complete after about two to three weeks for cattle hides and about one week for goat and sheep skins.
-
Store the cured hide — Once cured, the hide can be folded and stored in a cool, shaded, airy store, on wooden stackers off the ground and away from rain and direct sunlight, until it is taken to the tannery. Check stored hides every few days: red or purple patches, a bad smell or loose hair mean that more clean salt is needed at once.
Hides and skins can also be cured by soaking them in a strong salt solution called brine. This suits small skins and salts every part evenly.
- Estimate the water — The hide must be completely covered and free to move. Allow about 4 to 5 litres of water for every kilogram of hide.
- Prepare the salt solution — Pour clean water into a plastic container and stir in salt until no more will dissolve. This takes about 3.5 kg of salt for every 10 litres of water. A little undissolved salt left at the bottom shows that the brine is strong enough.
- Soak the hide — Put the washed, trimmed hide into the brine and press it under the surface. Stir or turn it several times so that no part stays folded.
- Time the soak — Leave goat and sheep skins for about 12 hours and cattle hides for up to 24 hours.
- Drain and finish — Lift the hide out and hang it over a water horse to drain. Then sprinkle fresh salt on the flesh side and stack it, or dry it in the shade (dry salting).
| Point | Salting | Air drying |
|---|---|---|
| How it preserves | Salt draws water out and stops bacteria growing | Moving air removes the water |
| What is needed | Plenty of clean salt and a shaded place | A drying frame, shade and dry weather; no salt |
| Condition of the hide | Stays damp and flexible, and soaks back quickly at the tannery | Becomes hard and stiff, takes much longer to soak back, and cracks if folded |
| Main risks | Too little salt or dirty salt leads to red patches and rotting | Hot sun damages the hide, slow drying in wet weather lets it rot, and insects attack it |
A farmer in Morogoro slaughters a cow and obtains a raw hide weighing 15 kg. Calculate the amount of salt required.
Using the 30% rule:
- Salt needed = 15 kg × 0.30 = 4.5 kg of salt
If the farmer uses 40%:
- Salt needed = 15 kg × 0.40 = 6 kg of salt
So the farmer should apply between 4.5 kg and 6 kg of salt to preserve this hide properly.
- Salt immediately after flaying — do not wait
- Apply salt to the flesh side (inner side) of the hide
- Use coarse, dry salt at 30–40% of hide weight
- Stack salted hides to allow brine to drain
- Re-salt thick hides after 24 hours if needed
- Always wear protective clothing when handling raw hides
- Using fine or wet salt — it dissolves too quickly and is less effective
- Salting only the edges — the entire surface must be covered
- Stacking hides before salt is applied — every hide in the pile needs its own full layer of salt on the flesh side
- Delaying salting — bacteria start working within hours
| Tool | Purpose |
|---|---|
| Workbench / Tannery beam | Surface for trimming and salting; a hide can also drain over a beam |
| Flaying knife | Removing fat and flesh residues |
| Salt container | Storing and dispensing salt |
| Wooden stackers | Raised, sloping platforms on which salted hides are piled so that the brine drains away |
| Buckets | Collecting brine/drainage water |
| Plastic containers | Holding the salt solution (brine) for soaking |
| Water horse / Leather horse | Trestles over which wet hides are hung to drain |
| Rubber gloves, overall, boots, mask | Personal protective equipment |
- Always wear rubber gloves to protect hands from bacteria and salt irritation
- Wear safety boots to prevent slipping on wet floors
- Use a dust coat or overall to protect clothing
- Wear a mask to avoid inhaling dust from dry salt and hide particles
- Work in a well-ventilated area
- Cover cuts and scratches with a waterproof dressing before work: salt stings in open wounds and raw hides carry germs
- Lift heavy wet hides with a partner and keep your back straight
- Do not handle hides from animals that died of disease, because diseases such as anthrax can pass to people
- Wash your hands and arms with soap and clean water when you finish
- Sweep up spilt salt and scraps, and scrub the workbench, beam, stackers, buckets and containers with clean water
- Wash and dry the knives and store them with the blades covered; salt left on metal causes rust quickly
- Keep unused salt dry in a covered salt container
- Do not pour brine or salty wash water onto crops or into streams, wells or ponds, because salt kills plants and spoils water. Pour it into a soak pit away from water sources
- Bury fat and flesh scraps in a pit away from houses
In many Tanzanian villages, cattle, goats, and sheep are slaughtered for food and trade. A livestock keeper in Mwanza who slaughters two cattle for a local market must preserve the hides immediately using salt to prevent them from rotting before selling them to a local tannery. By properly salting a 15 kg hide with about 5 kg of coarse salt and keeping it stacked under salt in the shade, the keeper can keep the hide in good condition for weeks, earning extra income by selling quality preserved hides at a fair price, a meaningful contribution to a rural household budget.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to appropriately:
- Inspect leather defects
- Handle tools and equipment
- Prepare salt solution
- Soak raw hide and skin
- Observe safety
- Clean hides and skin
- Clean tools and equipment
- Store raw hides and skins
- Store tools and equipment
Tathmini ya matokeo
Salt is concentrated into raw hides and skins as per the required specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Prepare salt solution
- Salt raw hides and skins
Principles: The student should explain the principles related to: Salting raw hides and skins
Theories: The student should explain:
- Differences between salting and dry methods
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions when salting raw hides and skin
- Safe handling of working tools and equipment
Swali
Why must salt be applied to raw hides immediately after flaying?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado