Mada za sehemu hiiPreserving raw hides and skinsMada 5
Stage beams, also called beam work, is the stage of rural tanning in which a raw hide or skin is soaked until it is soft and then worked over a tannery beam to clean it. In this activity the soaking liquid is a bran solution.
A tannery beam is a strong, smooth, rounded length of wood, often half a log, set on a slope with its top end at about waist height. The wet hide is laid over the curve. Because the hide rests on a firm, rounded surface, the knife touches only a narrow strip at a time, so the worker can push dirt, flesh and fat off without cutting holes.
A bran solution is bran (the husks of maize, wheat or rice) mixed with warm water and left until it turns slightly sour. Soaking a hide in this liquid:
- puts back the water that the hide lost when it was dried or salted
- loosens dirt, dung, blood and salt
- softens the hide so that it lies flat on the beam and is easy to work
Rural tanners worked hides by hand over a log or beam long before machines existed, using local materials such as bran, wood ash, lime and tree bark.
| Tool | Purpose |
|---|---|
| Tannery beam or wooden beam | Supports the wet hide while it is scraped |
| Water horse | A trestle over which wet hides are hung to drain |
| Kitchen knife | Scrapes off dirt, flesh and fat |
| Hard broom | Scrubs the hair side and sweeps the floor |
| Plastic containers | Hold the bran solution and the soaking hides |
| Buckets | Carry and measure water |
| Hammer | Drives in the pegs or wedges that keep the beam steady |
| Workbench | For laying out tools and trimming |
Wear rubber gloves, safety boots, an overall or dust coat and a mask throughout.
- Estimate the water. The hide must be completely covered and free to move. A goat skin needs about 10 litres; a cattle hide needs a much larger container and several times as much water.
- Measure about 1 kg of bran for every 10 litres of water.
- Put the bran in a plastic container and pour on warm water. The water should feel comfortably warm to the hand, never hot, because hot water damages raw hide. Stir well.
- Cover the container and leave it for about a day, until the liquid smells slightly sour.
Step 1: Set Up
Lay out the tools and put on your safety gear. Set the beam firmly so that it cannot rock or slide, using the hammer to drive in its pegs or wedges. Run your hand along the beam: it must be clean and smooth, because any lump or splinter under the hide will make the knife cut a hole.
Step 2: Wash the Hide
Rinse the hide in a bucket of clean water and scrub the hair side with the hard broom to remove dung, blood and loose salt. Change the water when it becomes dirty.
Step 3: Soak in the Bran Solution
Lower the hide into the bran solution and press it down until it is fully covered. Stir and turn it every few hours. A fresh or salted hide is usually ready after a night; a dried hide can need one to two days. The hide is ready when it is as soft and flexible as a fresh hide all over, including the thick neck and backbone. Do not soak for longer than needed: if the hair starts to pull out easily or the liquid smells rotten, take the hide out at once.
Step 4: Work the Hide on the Beam
Lift the hide out and hang it over the water horse for a few minutes to drain. Lay it over the beam, flesh side up, with its top edge hanging over the top end of the beam, and hold it in place by leaning against it. Hold the knife in both hands, almost flat, and push it downward and away from your body in overlapping strokes to remove loosened flesh, fat and dirt. Move the hide round so that each part in turn lies on top of the beam. Then turn the hide hair side up and stroke it with the back of the knife or the hard broom to push out dirty water.
Step 5: Rinse, Inspect and Drain
Rinse the hide in clean water. Check both sides for remaining flesh, dirt or hard, unsoaked patches, and rework them. Hang the hide over the water horse to drain.
- A soaked hide spoils quickly. Move it to the next stage the same day. If it must wait a few hours, leave it spread over the water horse in the shade, never folded in a heap.
- Do not pour used bran solution into or near a stream, pond or well. Pour it into a soak pit or onto a compost heap, and bury the scrapings in a pit away from houses.
- Scrub the beam, containers, buckets and broom with clean water and let them dry. Wash and dry the knife and store it with the blade covered. Keep the beam under cover and off the ground.
- Wash your gloves, boots and hands with soap.
- Always push the knife away from your body and keep your hands behind the cutting edge.
- Wet hides are heavy and slippery. Lift large hides with a partner and keep the floor swept and drained.
- Raw hides carry germs. Cover any cut with a waterproof dressing before work, and never handle a hide from an animal that died of disease.
- If you are cut, wash the wound with clean water, press on it with a clean cloth, cover it and report it.
A group of three students at a rural technical school in Morogoro received a salted goat skin. The day before the practical, they stirred 1 kg of maize bran into 10 litres of warm water and covered the container. By the next morning the liquid smelt slightly sour.
- Student A washed the skin and scrubbed the hair side with the hard broom.
- The group put the skin into the bran solution, turned it twice during the day and left it overnight.
- The following day Student B laid the soft skin over the beam and scraped the flesh side with downward strokes.
- Student C rinsed the skin, checked it and hung it on the water horse. The group then cleaned and stored the tools.
- Prepare the bran solution a day ahead, with warm water, never hot.
- Scrape downward, away from your body, with the hide lying smooth on the beam.
- Precision matters: a patch left hard or dirty will not take up salt, lime or tanning liquor evenly, and a single knife cut lowers the value of the whole hide.
- Working a hide that is not fully soaked, so that hard patches tear or stay dirty.
- Soaking for too long in warm weather, so that the hide starts to rot.
- Leaving folds or lumps under the hide on the beam, which leads to knife cuts.
- Leaving the wet hide in a heap after the work.
In regions such as Shinyanga and Mwanza, small-scale tanners soak and beam hides from local cattle and goats before turning them into leather for craftsmen who make sandals, belts and bags. A young person who can prepare a bran solution, soak a hide properly and work it cleanly over the beam can offer a useful service to local tanners, or start a small tanning business.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Prepare bran solution
- Use a tanning beam
- Observe safety
- Use bran solution
- Clean tools and equipment
- Store raw hides and skins
- Store tools and equipment
Tathmini ya matokeo
Raw hides and skins are soaked according to the required specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Use tannery beams
Principles: The student should explain the principles related to: Perform stage beams
Theories: The student should explain:
- History of rural tanning
- Uses of tanning beams
- Importance of precision and attention to details when performing stage beams
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions pertaining to perform stage beams
- Safe handling of working tools and equipment
Swali
What is the main purpose of soaking a hide in a bran solution before working it on the beam?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado