Mada za sehemu hiiDesigning and making ice making machineMada 7
An evaporator coil is a key component in a refrigeration system where the refrigerant absorbs heat from the surroundings, causing cooling. It is made from copper or aluminum tubing that is coiled to increase its surface area for efficient heat exchange. In a domestic refrigerator, the evaporator coil is located inside the freezer compartment or cooling section.
The evaporator coil serves two main functions:
- Heat Absorption: Cold refrigerant flowing through the coil absorbs heat from the air inside the refrigerator, causing the air to cool down.
- Moisture Removal: As warm air passes over the cold coil, moisture in the air condenses and drains away, keeping the refrigerator dry.
Evaporator coils are typically made from:
- Copper tubing — most common, easy to bend and has good heat conductivity
- Aluminum tubing — lighter and cheaper, but harder to joint
The tubing is usually 6mm to 12mm in diameter, depending on the refrigerator size.
The following tools are required for making an evaporator coil:
- Pipe benders (manual or mechanical)
- Bending springs or bending machine
- Tube cutter or hacksaw
- Reamer or deburring tool
- Measuring tools (tape measure, steel rule)
- Oxy-acetylene welding plant
- Soldering equipment (for joining)
- Drill and drilling machine
- Pop rivet gun
- Support brackets and mounting materials
- Safety gear (gloves, goggles, apron)
Step 1: Planning and Measuring
- Determine the required coil dimensions based on the refrigerator cabinet size
- Calculate the total length of tubing needed using the formula: L=N×(π×D)+(N−1)×S Where:
- L = total tubing length
- N = number of turns
- D = diameter of each turn
- S = spacing between turns
Step 2: Cutting the Tubing
- Measure and mark the calculated length on the copper tubing
- Cut the tubing using a tube cutter or hacksaw
- Remove burrs and sharp edges using a reamer
Step 3: Bending the Coil
- Insert a bending spring inside the tubing to prevent kinking
- Use the pipe bender or bending machine to create uniform turns
- Maintain consistent spacing between each turn (typically 25-40mm)
- Ensure each bend is smooth without wrinkles or flattening
Step 4: Forming Connections
- Create inlet and outlet connections at the correct positions
- Fit appropriate fittings (flare or solder-type) for connecting to the refrigeration system
- Ensure connections are tight and leak-free
Step 5: Mounting and Installing
- Attach mounting brackets to the coil using pop rivets
- Position the coil inside the refrigerator cabinet as designed
- Secure firmly to prevent vibration during operation
Step 6: Testing for Leaks
- Connect the coil to a vacuum pump to check for leaks
- Pressurize with nitrogen or refrigerant and check with leak detector
- Repair any leaks found before final installation
- Always wear safety goggles and gloves when cutting or bending metal
- Use proper lifting techniques when handling heavy equipment
- Keep the work area clean and free of oil or flammable materials
- Ensure adequate ventilation when using welding or soldering equipment
- Disconnect power supply when working on electrical components
A student needs to make an evaporator coil with 8 turns for a small refrigerator. The coil diameter is 150mm and spacing between turns is 30mm.
Calculation:
Number of turns (N) = 8 Diameter of each turn (D) = 150mm = 0.15m Spacing (S) = 30mm = 0.03m
Total straight length needed for the coil section: (N−1)×S=(8−1)×0.03=0.21m=210mm
Length for the curved sections: N×(π×D)=8×(3.142×0.15)=8×0.4713=3.77m
Total tubing length needed: L=3.77+0.21=3.98m≈4.0m
The student should cut approximately 4 meters of copper tubing to make this coil.
- Kinks or wrinkles in the tubing — caused by improper bending technique
- Inconsistent spacing — reduces cooling efficiency
- Leaky joints — results from poor soldering or improper fitting
- Incorrect coil size — leads to poor performance or compressor damage
In Tanzania, refrigeration technicians in cities like Dar es Salaam, Arusha, and Mwanza frequently repair and rebuild evaporator coils for domestic refrigerators and cold rooms at fish markets. For example, a technician at a local market might replace a faulty copper evaporator coil in a small shop refrigerator used to preserve fresh fish, charging around TZS 80,000 to 150,000 for the coil and installation. This skill also helps small business owners maintain their own refrigeration equipment, reducing costs of hiring external repair services.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Identify materials, tools and equipment required
- Draw a mechanical working drawing
- Draw electrical wiring circuit diagram
- Prepare body structure of the ice making system
- Assemble parts to form the machine
- Mount the mechanical refrigeration components
- Perform wiring circuits for Primary and Secondary circuits
- Perform plumbing
- Evacuate and charge with refrigerant
- Perform spray painting
- Apply safety gears appropriately
- Clean workplace, tools and equipment
- Store tools and equipment
- Commission the machine
Tathmini ya matokeo
Designed and made ice maker conform to technical and aesthetic specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Plan work
- Measure electrical to pressure quantities
- Determine system character
- Make different types of ice making units
- Form ice
Principles: The student should explain the principles of: (d) Heat transfer and exchange (e) System operating characteristics (f) Design parameters
Theories: The student should explain:
- Components functions
- Refrigeration cycle
- Refrigerants properties
- Heat load estimation
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling of working tools and equipment machines
- Plumbing
- Environmental Regulations
Swali
What is the most common material used for making evaporator coils in domestic refrigerators?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado