Mada za sehemu hiiDesigning and making ice making machineMada 7
A schematic diagram is a simplified drawing that shows how the different components of a refrigeration system are connected together. It uses standard symbols to represent each component, making it easy to understand how the system works without drawing realistic pictures. In this learning activity, you will learn to design and draw schematic diagrams for an ice making machine.
An ice maker is a device that produces ice by removing heat from water until it freezes. In refrigeration terms, it is a small-scale domestic refrigeration system designed specifically for making ice. The basic principle is the same as a refrigerator: a refrigerant absorbs heat from one area (the ice tray) and releases it elsewhere (the surrounding air).
Every refrigeration system has four main components that you must represent in a schematic diagram:
1. Compressor
The compressor is the heart of the system. It draws in low-pressure refrigerant vapor, compresses it to increase its pressure and temperature, and then pushes it toward the condenser. In schematic diagrams, the compressor is represented by a circle with the letter "M" inside (for motor) or a circle with the word "COMP" written below it.
2. Condenser
The condenser is a coil of pipe where the hot, high-pressure refrigerant releases its heat to the surrounding air and changes from a vapor to a liquid. In schematic diagrams, it is represented by a zigzag line or a coiled line, often labeled "COND."
3. Evaporator
The evaporator is where the cold refrigerant absorbs heat from the space (in this case, the ice tray or ice making compartment). It is represented by a coiled line similar to the condenser, but labeled "EVAP" or "EVAPORATOR."
4. Expansion Device
The expansion device (usually a capillary tube or expansion valve) reduces the pressure and temperature of the liquid refrigerant before it enters the evaporator. It is represented by a short line with a diamond shape at each end, or simply as a thin line with a label.
Follow these steps when designing a schematic diagram for an ice making machine:
Step 1: Identify the Purpose
Determine what the system needs to do—in this case, make ice. This helps you decide what components are needed.
Step 2: List All Components
Write down all the components your system will need:
- Compressor
- Condenser
- Expansion device (capillary tube)
- Evaporator (ice tray compartment)
- Suction line (pipe from evaporator to compressor)
- Discharge line (pipe from compressor to condenser)
- Liquid line (pipe from condenser to expansion device)
Step 3: Draw the Refrigeration Cycle
Using standard symbols, draw the components in the correct order following the refrigeration cycle:
- Start with the compressor on the left side
- Draw a line to the condenser (usually shown at the top or on the right)
- Draw a line from the condenser to the expansion device
- Draw a line from the expansion device to the evaporator
- Draw a line from the evaporator back to the compressor
Step 4: Add Labels and Direction Arrows
Label each component clearly. Draw arrows along the pipes to show the direction of refrigerant flow. This helps anyone reading the diagram understand how the system operates.
Step 5: Add Technical Details
Include important details such as:
- Temperature and pressure values at each point (if required)
- Type of refrigerant used (for example, R-134a)
- Power rating of the compressor
| Component | Symbol |
|---|---|
| Compressor | Circle with "M" inside |
| Condenser | Zigzag line or coiled line |
| Evaporator | Coiled line |
| Expansion valve | Diamond shape or thin line |
| Pipe/Line | Straight line |
| Direction of flow | Arrow |
Task: Draw a schematic diagram for a simple ice making machine using R-134a as the refrigerant.
Solution:
-
Start by placing the compressor at the center-left of your drawing paper. Label it "COMPRESSOR" and write "R-134a" below it.
-
Draw the discharge line from the compressor to the condenser (top of diagram). This line carries hot, high-pressure vapor.
-
Draw the condenser at the top as a zigzag line. Label it "CONDENSER." The refrigerant releases heat here and becomes a liquid.
-
Draw the liquid line from the condenser to the expansion device. This line carries cool, high-pressure liquid.
-
Draw the expansion device (capillary tube) as a thin line with a small restriction in the middle. Label it "CAPILLARY TUBE."
-
Draw the suction line from the expansion device to the evaporator. This line carries cold, low-pressure liquid.
-
Draw the evaporator at the bottom as a coiled line inside the ice-making compartment. Label it "EVAPORATOR (ICE TRAY)."
-
Draw the suction line returning from the evaporator back to the compressor, completing the cycle.
-
Add arrows along all pipes to show the clockwise or counterclockwise direction of refrigerant flow.
-
Add labels for each component and indicate the refrigerant type.
When drawing schematic diagrams, you may use:
- Drawing board and set square for accurate straight lines
- Tape measure if you need to scale your diagram to actual system dimensions
- Computer with CAD software for professional drawings (optional but recommended)
Always handle drawing tools carefully and keep your work area clean and organized.
- A schematic diagram uses standard symbols to show how refrigeration components connect
- The four main components are: compressor, condenser, expansion device, and evaporator
- Follow the refrigeration cycle when drawing: compressor → condenser → expansion → evaporator → compressor
- Always label components and add arrows to show the direction of refrigerant flow
- Use appropriate tools (drawing board, set square, CAD) for neat and accurate diagrams
In Tanzania, ice makers are commonly used in fish markets, restaurants, and small businesses to preserve perishable goods. For example, a fish vendor at the Kariakoo market in Dar es Salaam uses an ice making machine to keep fresh fish cold throughout the day. Being able to read and draw schematic diagrams helps technicians troubleshoot and repair these machines when they break down, ensuring that small businesses can continue operating without losing their stock.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Identify materials, tools and equipment required
- Draw a mechanical working drawing
- Draw electrical wiring circuit diagram
- Prepare body structure of the ice making system
- Apply safety gears appropriately
- Clean workplace, tools and equipment
- Store tools and equipment
- Commission the machine
Tathmini ya matokeo
Designed and made ice maker conform to technical and aesthetic specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Plan work
- Measure electrical to pressure quantities
- Determine system character
- Make different types of ice making units
- Form ice
Principles: The student should explain the principles of: (s) Heat transfer and exchange (t) System operating characteristics (u) Design parameters
Theories: The student should explain:
- Principle of drawing
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling of working tools and equipment machines
- Plumbing
- Environmental Regulations
Swali
What symbol is used to represent the compressor in a refrigeration schematic diagram?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado