Mada za sehemu hiiServicing domestic freezersMada 4
- Replacing evaporator coil
- Replacing compressor unit
- Replacing control elements
- Charging with refrigerant
Replacing Control Elements in Domestic Refrigeration Systems
Control elements are parts in a refrigerator that regulate its operation, ensuring the compressor runs at the right time and the temperature stays at the desired level. When these elements fail, the refrigerator may not cool properly, run continuously, or stop working entirely. Replacing faulty control elements is an essential skill in servicing domestic freezers.
1. Thermostat
The thermostat is a temperature-controlled switch that turns the compressor on and off based on the temperature inside the refrigerator. When the interior temperature rises above the setting, the thermostat contacts close and the compressor starts. When the temperature drops to the desired level, the contacts open and the compressor stops.
Application: If the freezer is too warm or the compressor runs all the time, the thermostat may need replacement.
2. Overload Protector (Thermal Relay)
The overload protector safeguards the compressor motor from overheating or drawing excessive current. It contains a bimetal strip that trips when the motor draws too much current or gets too hot, cutting power to the compressor.
Application: If the compressor frequently stops and starts, or fails to start at all, the overload protector may be faulty and requires replacement.
3. Start Relay
The start relay provides the initial boost of current needed to start the compressor motor. It works together with the overload protector to ensure proper starting and running of the compressor.
Application: If the compressor makes a humming sound but does not start, the start relay is likely defective.
4. Fan Motor
The fan motor circulates cold air throughout the freezer compartment. In frost-free refrigerators, it also helps distribute air over the evaporator coils to prevent frost buildup.
Application: If the freezer is not cooling evenly or you notice unusual noise, the fan motor may need replacement.
Step 1: Diagnose the Problem
Before replacing any control element, identify the faulty component through proper testing. Use a multimeter to check for continuity in thermostats, relays, and overload protectors. Inspect wiring for damage or loose connections.
Step 2: Disconnect Power
Always unplug the refrigerator or switch off the power supply at the mains before beginning any repair work. This prevents electric shock and protects the appliance from damage.
Step 3: Locate the Control Element
- Therstat: Usually found inside the refrigerator compartment, mounted on the control panel or wall.
- Overload Protector and Start Relay: Located near the compressor, usually on the side of the compressor housing.
- Fan Motor: Located at the back of the refrigerator near the condenser or inside the freezer compartment.
Step 4: Remove the Faulty Component
Use appropriate screwdrivers to remove screws holding the component in place. Take note of how wires are connected or photograph the wiring before disconnecting. For components connected with quick-connect terminals, use terminal pullers to avoid damaging the connectors.
Step 5: Install the New Component
Connect the wiring exactly as the original was connected, ensuring terminals are secure and properly seated. Mount the new component using the same mounting points and screws.
Step 6: Test the Repair
Reconnect the power and observe the refrigerator operation. Check that:
- The compressor starts and stops normally
- The thermostat maintains proper temperature
- No unusual noises or vibrations occur
Use a clamp-on amps meter to verify the compressor is drawing the correct current during operation.
- Always wear safety goggles when working with electrical components
- Use insulated tools to prevent electric shock
- Wear safety boots to protect feet from heavy components
- Work in a well-ventilated area
- Use a nose mask when handling old insulation or components that may contain dust
Problem: A domestic freezer in a household in Dar es Salaam is running continuously but the freezer compartment is not getting cold. The thermostat was tested and found to have no continuity at any temperature setting.
Solution:
- Disconnected power from the freezer
- Located the thermostat inside the freezer compartment
- Noted the wire connections and removed the faulty thermostat
- Installed a new thermostat of the same rating
- Reconnected power and adjusted the temperature dial to the desired setting
- Verified that the compressor now cycles on and off normally and the freezer reaches the set temperature
The freezer was returned to proper operation, saving the household from purchasing a new appliance.
In Tanzania, many households and small businesses rely on domestic freezers to preserve food, medicine, and ice for sale. When a freezer stops cooling properly due to a faulty thermostat or overload protector, a technician with skills in replacing control elements can repair it locally instead of importing a new refrigerator. This saves families money, supports local businesses like dukas and restaurants, and creates employment opportunities for technicians in communities across the country.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select appropriate tools and equipment
- Measure pressure and temperature quantities
- Identify type of refrigerant
- Determine correct quantity of refrigerant
- Charge a system with refrigerant
- Perform brazing
- Check electric circuits
- Store tools and equipment
- Clean workplace
Tathmini ya matokeo
A record of values of cold chamber temperatures, electrical quantities and pressure gauges conforming to the specified ratings
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Measure electric quantities
- Measure pressure quantities
- Connect simple electric circuits
- Identify refrigerant types
Principles: The student should explain the principles of: (h) Refilling a freezer with fresh refrigerant (i) Connecting electrical circuits in parallel, series and in combination (j) Making leakproof brazed or soldered joints (k) Taking different measurements of both electrical quantities and pressure quantities
Theories: The student should explain:
- Compression refrigeration cycle
- Types of electric circuit connections
- Compressor rating
- Freezers and assembly
Detailed knowledge about:
- Safe handling of working tools
- Safe handling of measuring instruments Environmental regulations
Swali
Which of the following is the primary function of a thermostat in a domestic refrigerator?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado