Mada za sehemu hiiServicing domestic freezersMada 4
- Replacing evaporator coil
- Replacing compressor unit
- Replacing control elements
- Charging with refrigerant
Charging with Refrigerant in Domestic Freezers
Charging with refrigerant is the process of adding the correct amount of refrigerant into a refrigeration system after it has been emptied for repair or maintenance. The proper charge is essential for the freezer to work efficiently and keep food cold.
A refrigerant is a special fluid that absorbs heat from the inside of the freezer and releases it outside. Common refrigerants used in domestic freezers include R-134a and R-600a. The correct type and amount of refrigerant must be used, or the system will not cool properly.
When a freezer develops a leak or needs repair, the refrigerant escapes or must be removed. After fixing the problem, fresh refrigerant must be added to restore cooling. Adding too little refrigerant causes poor cooling, while too much can damage the compressor and reduce efficiency.
There are two main methods taught at this level:
-
Charging by Weight (Weighing Method) – The refrigerant cylinder is placed on a charging scale, and the exact amount is measured as it enters the system. This is the most accurate method.
-
Charging by Observation – The technician watches the gauge readings and adds refrigerant until the system reaches proper operating pressures. This method requires experience.
Step 1: Prepare the System
- Connect the gauge manifold to the service ports on the compressor
- Ensure the system has been properly evacuated (air and moisture removed) using a vacuum pump
- Check that all joints are tight and no leaks are present
Step 2: Connect the Refrigerant Cylinder
- Connect the refrigerant cylinder to the high-side service port
- For R-134a, the cylinder should be upright (vapour charging)
- Open the cylinder valve slowly
Step 3: Add the Refrigerant
- If using the weighing method, note the initial weight on the scale
- Add refrigerant slowly while the compressor is running
- Watch the low-side pressure rise to the correct value (typically 0.8–1.2 bar for R-134a at normal room temperature)
Step 4: Verify Proper Operation
- Check that the freezer cools down to the correct temperature
- Ensure the compressor runs without overheating
- Use a leak detector to confirm no leaks at the connections
Step 5: Complete the Job
- Close the cylinder valve
- Remove the gauge manifold
- Record the amount of refrigerant added
- Wear safety boots and overalls at all times
- Work in a well-ventilated area – refrigerant gas can displace oxygen
- Keep open flames away – some refrigerants are flammable
- Do not overcharge the system
- Use a refrigerant identifier to confirm you are using the correct type
A domestic freezer uses R-134a refrigerant. The manufacturer's label states the system requires 150 grams of refrigerant. During a repair, all the refrigerant was lost. After fixing the leak and evacuating the system, the technician charges the freezer using a charging scale.
Procedure:
- Connect the gauge manifold and charging scale
- Place the R-134a cylinder on the scale and set to zero (tare)
- Start the compressor and slowly open the refrigerant cylinder valve
- Watch the scale reading – stop when it shows 150 grams added
- Close the cylinder valve and disconnect the equipment
Result: The freezer now contains the correct 150 grams of R-134a and should cool properly.
- Charging while the compressor is off (refrigerant will not circulate properly)
- Using the wrong type of refrigerant
- Adding refrigerant without evacuating the system first
- Overcharging, which causes high pressure and compressor damage
Charging with refrigerant is a critical skill in freezer servicing. Always use the correct type and amount of refrigerant, follow the proper procedure, and observe all safety measures. Proper charging ensures the freezer runs efficiently and lasts longer.
In Tanzania, many small businesses repair domestic refrigerators and freezers in towns like Arusha, Mwanza, and Dar es Salaam. A technician who correctly charges refrigerant can restore a neighbour's broken freezer, earning around TSh 30,000–50,000 for the job. Using the correct charge prevents the compressor from failing again, saving the customer the cost of buying a new refrigerator, which can cost TSh 400,000 or more.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Perform diagnostic trouble shooting
- Check refrigerant leaks
- Repair refrigerant circuit coils
- Repair damaged cabinet
- Charge refrigerant
- Test run
- Clean workplace
- Store tools and equipment
Tathmini ya matokeo
Demonstrate the ability of charging required amount of refrigerant in freezer and charge with refrigerant in domestic freezer conforms to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Control refrigerant being charged into freezer
- Identify refrigerant ozone global warming free
- Measure freezer pressure in pressure units
- Perform leak detection
Principles: The student should explain the principles of: (l) Heat transfer (m) Basic refrigerant cycle
Theories: The student should explain:
- Freezing concept
- Properties of refrigerant gas
- Sub cooling and super heating
Detailed knowledge about:
- Different refrigerant application
- Refrigerant properties
- Safe handling of refrigerants and tools
Swali
Charging with refrigerant is defined in the lesson as the process of:
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado