Mada za sehemu hiiServicing domestic freezersMada 4
- Replacing evaporator coil
- Replacing compressor unit
- Replacing control elements
- Charging with refrigerant
Replacing Evaporator Coil
The evaporator coil is a vital component inside a domestic refrigerator or freezer. It contains cold refrigerant that absorbs heat from the food compartment, keeping the inside cool. When the coil develops a leak, becomes clogged, or gets damaged, it must be replaced to restore the refrigerator's cooling ability.
The evaporator coil removes heat from the interior of the refrigerator. Over time, the coil can:
- Develop refrigerant leaks due to corrosion or physical damage
- Become blocked with ice or debris
- Lose efficiency due to wear
Replacing the coil restores proper cooling performance and extends the life of the refrigerator.
Before starting, gather the following tools and safety equipment:
Tools:
- Oxy-acetylene welding set
- Vacuum pump
- Pinch-off tool
- Dial type thermometer
- Rivet gun
- Hand drill machine
- Metal clips
- Screw drivers
- Hard brush
Safety Gear:
- Safety boots
- Overall (protective clothing)
- Safety goggles
- Nose mask
- Always disconnect the refrigerator from the power supply before working
- Wear protective clothing, goggles, and safety boots
- Use the nose mask when handling refrigerants or working with welding equipment
- Work in a well-ventilated area
- Handle the oxy-acetylene welding set with extreme care
Step 1: Recover the Refrigerant
Use the recovery equipment to safely remove refrigerant from the system. This prevents release into the atmosphere and complies with environmental regulations.
Step 2: Remove the Old Evaporator Coil
- Access the evaporator coil by removing the back panel or liner of the freezer compartment
- Disconnect the suction line and liquid line connected to the coil
- Use the pinch-off tool to seal the lines
- Remove mounting clips and brackets holding the coil in place
- Carefully withdraw the old coil from the cabinet
Step 3: Install the New Evaporator Coil
- Position the new coil in the correct location inside the freezer
- Secure it with metal clips and rivets using the rivet gun
- Connect the suction and liquid lines to the corresponding fittings
- Ensure all connections are tight and properly sealed
Step 4: Evacuate the System
Connect the vacuum pump to the system and run it for at least 30 minutes to remove moisture and non-condensable gases. This creates the vacuum needed for proper refrigerant charging.
Step 5: Charge the System
After evacuation, charge the system with the correct type and amount of refrigerant as specified by the manufacturer. Use the dial type thermometer to verify proper operating temperatures.
Step 6: Test and Inspect
- Power on the refrigerator
- Check for refrigerant leaks using a leak detector
- Monitor the temperature inside the freezer to ensure it reaches the desired level (typically -18°C for freezers)
- Verify that the compressor runs normally without unusual noises
- Refrigerant leaks: Often found at coil joints or due to corrosion
- Blocked coil: Caused by ice buildup or debris
- Faulty thermostat: May cause coil freezing or insufficient cooling
After replacing the coil, a technician tests the freezer temperature using a dial type thermometer. The thermometer reads -18°C at the evaporator surface. This confirms the system is operating correctly, as domestic freezers should maintain temperatures at or below -18°C.
- Keep the evaporator coil clean by brushing it regularly
- Ensure the freezer door seal is tight to prevent moisture ingress
- Defrost the freezer periodically to prevent ice buildup on the coil
In Tanzania, many households and small businesses (like butcheries and fish sellers) rely on domestic freezers to preserve food. When the evaporator coil fails, a technician can replace it using the skills from this topic, restoring the freezer's cooling function. This saves the owner from buying a new refrigerator, which can cost between TZS 500,000 to TZS 1,500,000, making refrigerator repair a valuable trade skill in local communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select appropriate tools and equipment
- Measure pressure and temperature quantities
- Determine the fault causes
- Identify type of evaporator copper pipe
- Determine correct size of evaporator and copper pipe to be replaced
- Charge a system with refrigerant
- Perform brazing
- Store tools and equipment
- Clean workplace
Tathmini ya matokeo
A record of values of cold chamber temperatures quantities and pressure gauges conforming to the specified ratings
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Measure pressure quantities
- Copper pipe bending technique
- Identify refrigerant types
Principles: The student should explain the principles of: (a) Refilling a freezer with fresh refrigerant (b) Making leakproof brazed or soldered joints (c) Taking different measurements of pressure quantities
Theories: The student should explain:
- Compression refrigeration cycle
- Types of copper pipes
- Compressor rating
- Freezers and assembly
Detailed knowledge about:
- Safe handling of working tools
- Safe handling of measuring instruments Environmental regulations
Swali
What is the main purpose of the evaporator coil in a domestic refrigerator?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado