Mada za sehemu hiiConstructing archesMada 3
Setting Arches
Setting arches is the process of designing, planning, and constructing an arch structure by using precise measurements, calculations, and layout to ensure the arch is both functional and aesthetically pleasing. This process includes setting out the arch's shape, dimensions, and position before construction begins. Arches efficiently transfer weight from above openings to the supporting abutments, eliminating the need for additional beams and allowing wider spans in doors, windows, and passages.
Understanding the terminology of arch components is essential for proper construction:
- Abutment: The end support of an arch.
- Intrados: The inner curve or surface of an arch.
- Extrados: The outer curve or surface of an arch.
- Voussoirs or arch stones: Wedge-shaped units forming the arch.
- Springing stone: The first voussoir at the springing level on either side of the arch.
- Springing line: An imaginary line joining the two springing points.
- Crown: The highest point of the extrados, or the highest part of an arch.
- Keystone: The highest central wedge-shaped block of an arch.
- Span: The clear horizontal distance between the inner faces of the two supports.
- Rise: The vertical distance between the springing line and the crown.
- Haunch of an arch: The portion of the arch situated centrally between the key and springing point.
- Striking point/centre: The centre point of an arch.
Classification by Construction Mode
- Masonry arch: Built from individual stone or brick units.
- Concrete arch: Made from reinforced concrete.
- Steel arch: Constructed from steel beams.
- Wooden arch: Used in traditional or lightweight structures.
Classification by Shape
- Semicircular arch: The curve is a half-circle; the centre lies on the springing line.
- Segmental arch: Forms a shallow curve, less than a semicircle.
- Gothic or pointed arch: Formed by two intersecting curves that converge to a pointed apex.
Classification by Number of Centres
| Type | Description |
|---|---|
| One-centred arches | Flat, segmental, circular, horseshoe |
| Two-centred arches | Pointed arches (Lancet and Drop) |
| Three-centred arches | Three-centred semi-elliptical, Florentine, Ogee |
| Four-centred arches | Venetian, Tudor |
| Five-centred arches | Five-centred semi-elliptical |
The process of setting out an arch involves precise measurements and geometric calculations.
Step-by-Step Procedure
-
Review the design: Identify the span (width), rise (height), shape, keystone position, and number of voussoirs.
-
Mark the centreline: Determine the central point of the arch span and use a chalk line or string to mark the vertical centreline on the wall or foundation.
-
Locate springing points: Measure half the span distance from the centrelines on both sides to mark where the arch curve begins.
-
Draw the curve:
- For a semicircular arch: Use a compass or trammel with a radius equal to half the span.
- For a segmental arch: Calculate the radius using the formula below.
- For a Gothic arch: Use two intersecting arcs with centres at the springing points.
-
Create a template: Transfer the arch curve onto plywood or cardboard to use as a guide during construction.
-
Mark voussoir positions: Divide the arch curve into equal segments, ensuring the keystone is centred and joints radiate from the centre.
-
Check measurements: Double-check span, rise, and curve. Use a spirit level to ensure springing points are level and symmetrical.
-
Transfer to construction surface: Use the template to transfer the arch design onto the construction surface.
-
Begin construction: Start from the springing points, working toward the keystone.
The radius (R) of a segmental arch is calculated using the formula:
R=8HS2+4H2
Where:
- S = span (horizontal distance between supports)
- H = rise (vertical distance from springing line to crown)
Worked Example
A garden gateway has a segmental arch with a span of 4 metres and a rise of 1 metre.
Solution:
R=8×142+4×12
R=816+4
R=820
R=2.5 metres
The radius of the segmental arch is 2.5 metres.
Centring is the temporary framework that supports an arch during construction. It holds all voussoirs in position until the keystone is placed and mortar is fully cured.
Key Points About Centring
- Typically made of timber (wood) because it is simple to erect, dismantle, and reuse.
- Must be precisely shaped to match the arch's intended curve.
- Must be strong enough to bear the weight of all masonry materials.
- Requires proper bracing to prevent movement during construction.
- Should be carefully dismantled after mortar cures to avoid disturbing the arch.
Steps for Constructing Centring
- Determine the shape and size of the arch.
- Create a template for the curve using a compass or flexible strip of wood.
- Construct a sturdy base frame using timber or metal supports.
- Cut wooden planks or plywood to match the curve.
- Assemble curved pieces onto the frame, securing with nails or screws.
- Add vertical and diagonal supports beneath the formwork.
- Use adjustable props or shims to fine-tune height and alignment.
- Verify alignment using a spirit level and measuring tape.
General Construction Steps
- Erect centring: Build the temporary support structure.
- Lay voussoirs: Place wedge-shaped stones or bricks in a radial pattern, starting from springing points.
- Set the keystone: Place the central wedge-shaped block last to lock all units together.
- Allow curing: Let mortar set and develop strength.
- Remove formwork: Carefully dismantle centring once the arch is self-supporting.
Key Considerations
- Load distribution: The arch must handle the intended weight.
- Aesthetics: The arch's shape should harmonise with architectural style.
- Material selection: Must balance durability, strength, and appearance.
- Formwork: Must be robust, true to line and level, and match design drawings exactly.
In Tanzania, the skill of setting arches is directly applied when constructing traditional Swahili-style buildings in Stone Town (Zanzibar) or when building modern commercial structures in Dar es Salaam where arched doorways and windows are desired for aesthetic appeal. A mason in Arusha might use this knowledge to construct a segmental arch for a restaurant entrance, calculating the radius as 2.5m for a 4m-wide opening with a 1m rise, using locally sourced timber for centring and burnt clay bricks for the voussoirs.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret drawings
- Prepare tools and equipment
- Clear the Area
- Mark the Opening
- Build Formwork
- Check Alignment
- Clean the work area and store tools
Tathmini ya matokeo
Arches are set as per technical specifications to provide aesthetic appeal and structural support over openings
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should explain the different procedures for setting arches
Principles: The student should explain the principles involved in setting arches
Theories: The student should explain:
- Types of arches
- Materials and their properties
- Tools and specific functions
- Different types of formwork Circumstantial knowledge:
Detailed knowledge about:
- Safety procedures to be observed when setting arches
- First aid
- Environmental issues
Swali
Which part of an arch is defined as the inner curve or surface?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado