Mada za sehemu hiiMaking up right furnitureMada 4
- Making stool/table
- Making bed
- Making shelf
- Making chair
Making a Shelf
A shelf is a horizontal structural component used for storing or displaying books, files, and other important documents. Shelves are essential furniture pieces found in homes, libraries, offices, and schools. They can be open (without doors) or closed (with doors), depending on their use and where they will be placed.
Based on the textbook, shelves can be classified according to their installation method:
- Open or closed shelf – depends on whether it has doors or not
- Freestanding units – stand on the floor without additional support from walls or ceiling
- Hung units – rely on walls and/or ceiling for support
- Fitted units – freestanding or hung units that need fixing to walls, floors, or ceilings for stability
- Built-in fitments – rely fully on attachment to floor, wall, or ceiling for structural framework and stability
A simple shelf typically consists of:
- Legs or sides – vertical members that support the shelf
- Shelf boards – horizontal surfaces for placing items
- Rails – horizontal connectors between legs (optional for simple shelves)
For Form 1 level, the following joints are commonly used:
-
Mortise and tenon joint – a strong joint where a tenon (projection) on one piece fits into a mortise (hole) on another piece. This is commonly used to join legs to rails.
-
Housing joint (groove) – a channel cut into a board to receive the end or edge of another board. This is used for fixing shelf boards between two sides.
Follow these steps in order:
-
Interpret the working drawing – study the design, dimensions, and layout of the shelf to understand what you need to make.
-
Prepare a cutting list – list all pieces needed with their sizes.
-
Select materials – choose timber pieces that are free from defects like knots, cracks, or warping.
-
Select tools and equipment – gather cross cut saw, tenon saw, tape measure, try square, pencil, F clamp, mortice chisel, marking gauge, mallet, hand drill, plough plane, sash clamp, and workbench.
-
Prepare shelf members – saw and plane timber to required sizes (refer to timber preparation procedures).
-
Set out legs/sides – mark positions for joints and grooves on the leg pieces according to the working drawing.
-
Set out shelf boards – mark where shelf boards will be positioned.
-
Chop mortise or cut groove – cut the mortise holes in legs for tenons, or cut housing grooves for shelf boards.
-
Cut tenon or housing – prepare the corresponding tenons on rails or housing channels for shelf boards.
-
Trial fitting – assemble the pieces without glue to check that all joints fit tightly and the frame is square.
-
Assemble the shelf – apply glue to joints and clamp the frame together using sash clamps. Leave to dry.
-
Clean the shelf frame – remove excess glue and smooth any rough areas.
-
Fix shelves – insert shelf boards into grooves and secure if necessary.
-
Perform sanding – start with coarse sandpaper, then progress to fine sandpaper for a smooth surface.
-
Apply finishing – use varnish, clear coat, or paint to protect the wood.
-
Clean workplace and return tools – sweep the workshop and put all tools back in the store.
Always observe these safety measures when making a shelf:
- Wear overalls
- Wear safety goggles
- Wear safety boots
- Use the right tool for each job
- Keep the workplace clean and tidy
- Return tools to the store after use
A student needs to make a simple open shelf for storing books. The working drawing shows:
- Two side pieces: 600 mm long × 100 mm wide × 20 mm thick
- Three shelf boards: 400 mm long × 100 mm wide × 20 mm thick
- One top rail: 400 mm long × 50 mm wide × 20 mm thick
Procedure followed:
- The student interpreted the drawing and prepared a cutting list.
- Selected clear timber free from knots.
- Prepared each piece by cross-cutting to length and planing edges square.
- Set out positions for housing joints at 150 mm, 300 mm, and 450 mm from the bottom on both side pieces.
- Used a plough plane to cut 20 mm wide housing grooves.
- Cut shelf boards to fit into the grooves (slightly smaller than the groove depth to allow for expansion).
- Trial assembled the frame – all joints fitted correctly.
- Glued and clamped the frame, left to dry for 24 hours.
- Sanded all surfaces starting from 120 grit to 240 grit sandpaper.
- Applied two coats of clear varnish and allowed drying between coats.
In Tanzania, shelves are commonly used in homes to store books, kitchen utensils, and clothing. A small business owner in Dar es Salaam might make a simple shelf to display soap, cooking oil, and other items in their dukaliving room. The skills learned in making shelves can also help students assist their families in building or repairing storage furniture at home, saving money that would otherwise be spent on buying new furniture from carpentry workshops.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Draw shelf
- Interpret the drawings
- Calculate materials required
- Select tools equipment and materials
- Prepare members
- Set out joints
- Make joints
- Assemble the shelf
- Apply finishes
- Clean the work area
- Store the shelf and tools to their place
Tathmini ya matokeo
The constructed shelf conforms to drawing and technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should be able to explain methods related to make shelf
Principles: The student should explain principles related to make shelf.
Theories: The students should explain theories related to make shelf
Circumstantial knowledge: The students should explain detailed knowledge related to make shelf
Swali
Which of the following best describes a shelf in furniture making?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado