Mada za sehemu hiiMaking up right furnitureMada 4
- Making stool/table
- Making bed
- Making shelf
- Making chair
Making a Chair
A chair is a piece of furniture with a raised surface, commonly used to seat a single person. Chairs are supported most often by four legs and have a back; however, a chair can have three legs or can have a different shape.
A chair consists of several important parts:
- Seat: The horizontal surface where a person sits
- Back: The vertical part that supports the sitter's back
- Legs: The vertical members that support the chair
- Rails: Horizontal members between legs:
- Top rails: Fixed on the upper part of the legs
- Bottom rails: Fixed on the lower part of the legs
Chairs can be classified based on their design and purpose:
- Stool - A raised seat supported by three or four legs, without armrests or backrest
- Office chair - Designed for use at a desk, with backrest and armrest
- Dining chair - Simple chair used in dining rooms
- Armchair - Chair with armrests on both sides
Chair dimensions are determined by anthropometric measurements (human body measurements). The most relevant measurements are:
| Measurement | Description |
|---|---|
| Seat height | Distance from floor to seat surface |
| Seat width | Width of the seating area |
| Back height | Height of the backrest |
| Overall height | Total height from floor to top of back |
Follow these systematic steps to make a quality chair:
Step 1: Interpret the Working Drawing
Study the given drawing to understand the chair's design, dimensions, and construction details.
Step 2: Prepare a Cutting List
List all timber pieces required with their exact dimensions:
- 4 legs
- 2 front rails
- 2 back rails
- 1 seat
- 1 back (or back slats)
Step 3: Select Materials
Choose timber that is free from defects such as knots, cracks, and warping. The timber should be properly seasoned.
Step 4: Select Tools and Equipment
Gather all necessary tools:
- Cross cut saw and Tenon saw
- Tape measure and Try square
- Pencil and Marking gauge
- Mortice chisel and Mallet
- F clamp and Sash cramp
- Bench vice and Workbench
Step 5: Prepare Chair Members
Using the timber preparation procedures:
- Select face side and face edge on each piece
- Plane all pieces to required sizes
- Mark out all components according to the drawing
Step 6: Set Out Legs
Mark the positions for mortises on each leg according to the working drawing. Use the try square to ensure marks are square.
Step 7: Set Out Rails
Mark the tenon positions on the rails. Ensure the tenons will fit properly into the mortises.
Step 8: Chop Mortises
Cut mortise holes in the legs using a mortice chisel and mallet. The mortise must be clean and square.
Step 9: Cut Tenons
Cut tenons on the rail ends to fit the mortises. The tenon should be slightly smaller than the mortise to allow for glue.
Step 10: Trial Fitting
Assemble the chair frame without glue to check:
- Tightness of joints
- Squareness of all corners
- Overall dimensions
Step 11: Cut Seat to Size
Cut the seat timber to the required dimensions and shape as per drawing.
Step 12: Final Assembly
- Apply wood glue to all joints
- Assemble the chair frame
- Use sash cramp to tighten joints
- Allow glue to dry completely
Step 13: Fix the Seat
Attach the seat to the frame using appropriate fasteners or glued joints.
Step 14: Perform Sandpapering
Sand all surfaces starting from coarse sandpaper (80-120 grit) to fine sandpaper (180-220 grit).
Step 15: Apply Sanding Sealer
Apply sanding sealer to fill wood pores. After drying, lightly sand with fine paper.
Step 16: Apply Finishing
Apply the final finish such as varnish, clear coat, or paint using a brush.
Step 17: Clean Workplace
Clean the workshop and return all tools to their proper storage.
Always observe these safety measures when making a chair:
- Wear overall protective clothing
- Wear safety goggles when cutting orchiselling
- Wear safety boots to protect feet
- Use the correct tool for each job
- Keep the workplace clean and tidy
- Return tools to storage after use
- Always cut on the waste side of marked lines
Problem: A student needs to make a simple chair with the following specifications:
- Seat size: 400mm × 400mm
- Leg height: 450mm
- Back height: 400mm from seat
- Legs and rails: 25mm × 25mm
Solution:
- Cut 4 legs at 450mm length
- Cut 2 front rails and 2 back rails at 350mm length
- Cut seat at 400mm × 400mm
- Cut back slats or back frame at required dimensions
- Cut mortises in legs at 50mm from top
- Cut tenons on rail ends to fit mortises
- Assemble and finish
In Tanzania, chair-making skills are valuable for small carpentry businesses in towns like Arusha, Mwanza, and Dodoma, where artisans produce furniture for homes, schools, and offices. A Form 1 student could use these skills to repair broken chairs at home or start a small business making simple chairs to sell at local markets, earning money to support school expenses or family needs.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Draw upright furniture
- Interpret the drawings
- Calculate materials required
- Select tools equipment and materials
- Prepare members
- Set out joints
- Make joints
- Assemble the furniture
- Apply finishes
- Clean the work area
- Store the furniture and tools to their place
Tathmini ya matokeo
Constructed chair conforms to drawing and technical specifications
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should be able to explain methods related to make chair
Principles: The student should explain principles related to make chair
Theories: The students should explain theories related to make chair
Circumstantial knowledge: The students should explain detailed knowledge related to make chair
Swali
What is the main function of the back of a chair?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado