Mada za sehemu hiiDehairing raw hides and skinMada 5
Scraping hair out is the process of removing hair and the outer layer of tissue from a raw hide or skin after it has been soaked in lime solution, which loosens the hair. This is one of the most important steps in preparing leather for tanning. The purpose is to clean the hide so that only the strong leather layer remains. Without proper scraping, the leather will be rough, uneven, and of poor quality.
When an animal is slaughtered, the hide still has hair, fat, flesh, and dirt attached to it. The hide must be cleaned before it can be turned into useful leather. Scraping does three things:
- Removes the hair from the surface of the hide
- Removes the epidermis (thin outer skin layer), which would block the tanning liquor and leave a rough surface
- Helps the hide absorb tanning chemicals evenly in the next steps
Hair left on the pelt causes problems later. Tanning liquor cannot enter properly under a patch of hair, so the leather there stays hard, tans unevenly and takes dye badly. Short hairs and hair roots left in the surface make it rough and lower the grade of the leather. The surface under the hair is the grain, the most valuable part of the leather, so the work must be careful and exact: every scratch made now shows in the finished leather.
Before starting, gather all the following tools and put on your safety equipment:
- Curved panga or kitchen knife (the main scraping tool, used with its blunt back edge)
- Leather horse or workbench (to support the hide while it is scraped)
- Hand broom (to brush away loose hair)
- Buckets (for water and waste)
- Rubber gloves (to protect your hands)
- Safety boots and overall/overcoat
- Mask (to keep splashes of lime water away from your nose and mouth)
Step 1: Prepare the Work Area
Set up your working shade — a covered area that protects you and the hide from direct sunlight and rain. Place the workbench or leather horse in a stable position. Fill a bucket with clean water for rinsing the blade and your hands.
Step 2: Prepare the Limed Hide
The hide must first have been washed, soaked soft and then kept in lime solution for several days. It is the lime, not plain water, that loosens the hair. Check each hide before you start: rub the hair on the neck with a gloved thumb. If it slips off easily the hide is ready; if it still holds, return the hide to the lime. Sort the hides so that those of similar size and thickness are worked together. Wearing gloves, lift the hide out of the lime, let it drain over the container, rinse it in clean water and lay it hair side up across the leather horse or workbench. The hide must be held tight so that the surface is flat and easy to scrape.
Step 3: Scrape the Hair Using the Curved Blade
Hold the curved panga or kitchen knife firmly. Start from one edge of the hide and work your way to the other side using smooth, controlled strokes. The blade should be angled slightly downward — about 30 to 45 degrees — so that it slides under the hair and pushes it off together with the thin outer layer of skin. Use the blunt back of the blade, not the sharp edge: the loosened hair only needs to be pushed off, and a sharp edge would cut the grain.
Key technique: Push the blade away from your body in the same direction as the hair growth. Do not dig the blade in too deeply or you will damage the hide and cut holes in the leather. Apply steady, even pressure.
Work in straight lines from top to bottom or side to side, moving across the whole surface. The hair and thin outer skin will come off in strips. Use the hand broom to sweep away the loose hair so it does not pile up and block your work.
Step 4: Rinse and Inspect
Once you have scraped the entire surface, rinse the hide with clean water to remove any remaining loose tissue and hair. Inspect the hide carefully — there should be no patches of hair left, and the surface should feel smooth and clean. If any hair remains, scrape those areas again.
Step 5: Clean and Store
After scraping, wash the pelt (the name for a hide once its hair is off) one more time and hang it over a leather horse to drain. It is now ready for the next stages: scraping the flesh side and removing the lime. Do not let the pelt dry out. If it must wait, keep it in clean water or under wet sacking in the shade, and for no longer than a day.
Wash the panga, knife, hand broom, buckets and leather horse with clean water, dry the blades and store all tools in a dry, safe place with the edges covered. Wash your gloves, boots and overall.
- A limed hide is caustic and very slippery. Wear rubber gloves, boots and an overall, protect your eyes from splashes, and keep a firm hold on the hide
- Scrape away from your body and keep your free hand behind the blade
- Keep the floor swept and drained so that nobody slips on hair and water
- If lime water splashes on the skin, wash it off with plenty of clean water. If it gets into an eye, rinse the eye with clean running water for at least 15 minutes and go to a health facility
- For a cut, wash the wound well with clean water, press on it with a clean cloth to stop the bleeding, cover it and report it. A deep cut needs a health facility
- Collect the scraped hair and bury or compost it in a pit away from houses and water sources. Never throw hair or lime water into a stream, pond or well
Example: Hassan has kept a goat skin in lime solution for four days, and the hair on the neck now slips off when he rubs it. He rinses the skin in clean water. He stretches it on a leather horse and begins scraping. He holds the blunt back of the curved panga at an angle of about 40 degrees and pushes it smoothly from the top of the skin toward the bottom, brushing away loose hair with a hand broom after each pass. After scraping the entire surface, he rinses the skin and finds a small patch of hair near the edge that was missed. He returns the skin to the leather horse and scrapes that patch again before rinsing. The clean pelt is now ready for fleshing and the removal of lime.
- Scrape only after the lime has loosened the hair
- Keep the hide stretched tight on a leather horse or workbench
- Use the curved blade at an angle of 30–45 degrees
- Scrape in smooth, controlled strokes away from your body
- Remove all hair and the thin outer skin layer
- Rinse the hide thoroughly after scraping
- Wear protective clothing — gloves, boots, mask, and overall
- Scraping before the lime has loosened the hair, or scraping a hide that has dried (the hair will not come off easily and you will damage the grain)
- Holding the blade too steeply (you will cut into the hide and ruin it)
- Pressing too hard (this creates holes and thins the leather unevenly)
- Forgetting to wear protective gloves (the limed hide is caustic and slippery)
- Using the sharp edge of the blade on the hair side (it scratches the grain)
In Tanzania, many rural families keep livestock such as goats, cattle, and sheep for income and food. After slaughtering an animal, the hide is sometimes thrown away or left to rot. By learning to scrape hair out properly, a young person can turn these raw hides into clean pelts, and then into leather that can be sold to local craft makers or used to make shoes, bags, and belts for sale at the market. A cleanly scraped skin fetches a better price than a patchy one, making proper scraping techniques a valuable skill for earning income in many Tanzanian communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select material
- Select tools and equipment
- Grade raw hides and skins
- Wash hides and skins
- Inspect for quality
- Scrap hair out
- Observe safety
- Clean tools and equipment
- Store pelt
- Store tools and equipment
Tathmini ya matokeo
The hair is scraped out on a pelt surface as per the required standards
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Scrap hair out
- Prepare pelt for next stages
Principles: The student should explain the principles related to:
- Scraping hair out on a pelt
Theories: The student should explain:
- Effects of remaining hair on pelt
- Importance of precise and detailed work while scraping hair out
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions pertaining to handling scraping tools
- First Aid
- Waste disposal
Swali
Why must the hair and the thin outer skin layer be scraped off a limed hide before tanning?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado