Mada za sehemu hiiDehairing raw hides and skinMada 5
Removing lime (also called deliming) is the process of taking out calcium hydroxide (lime) from hides and skins after the unhairing stage. During liming, hides are soaked in a lime solution to swell the fibres and help loosen the hair. After the hair is removed, the lime must be washed out before the hide can move to the next tanning steps.
- Lime makes the hide too alkaline (high pH), which can damage the leather fibres
- Lime left in the pelt makes the leather stiff, hard, and rough, and it reacts with vegetable tanning liquor to cause dark stains and a brittle grain that cracks
- Removing lime brings the pH down to a level suitable for the next stages, bating (further softening) and tanning
- Clean hides absorb tanning agents better, producing higher quality leather
- Washing in clean water — Repeatedly soaking and agitation to flush out lime
- Using ammonium salts — Ammonium chloride or ammonium sulphate is dissolved in the water to neutralise the lime
- Using organic acids — Weak acids such as lactic acid or formic acid, well diluted in water, are used
- Using a bran drench — Bran is mixed with warm water and left for about a day until it turns sour. The weak natural acids in the sour liquid remove lime gently and leave the pelt soft. This is the traditional rural method
Washing with clean water always comes first, but water alone removes only the loose lime near the surface. A deliming material is needed to remove the lime held inside the pelt. In rural tanning, a bran drench or an ammonium salt (ammonium sulphate is sold as a fertiliser) is the usual choice, because both are cheap and mild.
Step 1: Prepare the workspace Set up a clean working shade with plastic containers or a tan pit filled with clean water. Estimate the water: the pelt must be fully covered and able to move, which takes about 3 to 4 litres for every kilogram of pelt. Have the tannery beam ready for scraping.
Step 2: Rinse the pelt Check that dehairing is complete and scrape off any hair that is left. Place the dehaired pelt in clean water. Agitate or stir it for 10–15 minutes, then change the water and repeat two or three times. This washes out the loose lime.
Step 3: Prepare the deliming solution and dip the pelt Weigh the pelt. For ammonium sulphate or ammonium chloride, dissolve 1–2 kilograms in water per 100 kilograms of pelt, which is 10 to 20 grams for each kilogram. Dip the pelt in this solution for 30–60 minutes, stirring often; thick hides in a still container can take two hours or more. For a bran drench, use about 1 kg of bran to 10 litres of warm (not hot) water, let it turn sour, and leave the pelt in it overnight.
Step 4: Test for completion There are three ways to check. By feel: a limed pelt is swollen, rubbery and slippery, while a delimed pelt is soft and limp, and a thumb pressed into it leaves a mark that stays. With indicator: cut a thin slice from the thickest part (the neck) and put a drop of phenolphthalein on the cut; pink shows that lime remains, and no colour shows that deliming is complete. With pH paper pressed on the cut: the pelt is properly delimed when the pH reaches 8–9 (slightly alkaline but not strong).
Step 5: Final rinse Give the pelt one or two more rinses in clean water to remove any remaining lime or chemicals. Then lay the pelt over the tannery beam, grain side up, and stroke it downward with the blunt back of a knife to squeeze out dirty water, hair roots and loosened lime. Rinse once more.
Step 6: Inspect the pelt Check that the hide feels soft, clean, and free of lime deposits before proceeding to the next stage. A delimed pelt has lost the lime that held back bacteria and it rots quickly, so move it on the same day. If it must wait a few hours, keep it under clean, cool water in the shade; never leave it in a heap or let it dry.
- Wear rubber gloves and a mask when handling chemical deliming agents
- Work in a well-ventilated area or outdoors
- Avoid direct skin contact with lime solutions
- Wash hands thoroughly after handling pelts
- Ammonium salts give off ammonia gas when they meet lime. Its sharp smell irritates the eyes and chest, so delime only in the open working shade, never in a closed room, and do not lean over the container
- Keep fertiliser salts and acids labelled, closed and away from food. Any acid used must be weak and well diluted: always add acid to water, never water to acid
- First aid: wash any chemical or lime off the skin with plenty of clean water. If it gets into an eye, rinse with clean running water for at least 15 minutes and go to a health facility. Move anyone who feels unwell from fumes into fresh air
- Scrub the containers, buckets, beam and tools with clean water, dry them and store them under cover; store knives with the blades covered
- Used deliming liquid and wash water contain lime, salts and bits of skin. Do not pour them into streams, ponds or wells or onto crops. Pour them into a soak pit away from water sources
- Bury hair and scrapings in a pit away from houses
- Removing lime is also called deliming
- The goal is to lower the pH of the hide after liming
- Washing removes loose lime; a mild deliming material such as an ammonium salt or a bran drench removes the rest
- The pelt is ready for the next stage when it feels soft and has a pH of about 8–9
- Always use protective gear when handling chemicals
In rural Tanzania, a village tanner who has just dehaired goat skins can apply this process to prepare the skins for tanning. By properly removing lime, the tanner produces softer, higher-quality leather that earns a better price than leather from poorly delimed skins. This skill helps small-scale tanners earn a sustainable income and supply local cobblers with good leather for making shoes.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select material
- Select tools and equipment
- Set tannery beams
- Grade raw hides and skins
- Wash hides and skins
- Inspect for quality
- Estimate amount of water
- Perform dehairing
- Wash the pelt
- Prepare deliming solution
- Dip the pelt into the deliming solution
- Check for deliming completion
- Wash and remove the deliming solution
- Clean the pelt
- Observe safety
- Clean tools and equipment
- Store pelt
- Store delimed hides and skins
- Store tools and equipment
Tathmini ya matokeo
The lime is removed in a pelt as per required specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Use tannery beams
- Prepare deliming solution
- Make tests for deliming process
- Prepare pelt for next stages
Principles: The student should explain the principles related to:
- Making deliming solution
- Handling deliming solution
- Handling various lime yard materials, tools and equipment
Theories: The student should explain:
- Uses of materials and their properties
- Types of deliming materials
- Importance of precise and detailed work while performing dehairing raw hides and skins
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions pertaining to handling deliming materials
- First Aid
- Waste disposal
Swali
What is the correct term for the process of removing calcium hydroxide (lime) from hides after unhairing?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado