Mada za sehemu hiiDesigning and making domestic refrigeratorMada 6
- Designing and draw a refrigerator schematic diagram
- Making evaporator coil
- Constructing refrigerant pipe circuit
- Installing electrical wiring circuit
- Charging and commissioning the system
- Making clutter in refrigerator
Designing and Drawing a Refrigerator Schematic Diagram
A schematic diagram is a simplified drawing that shows how the different parts of a refrigerator are connected together using standard symbols. It uses simple shapes and lines instead of realistic pictures, making it easier to understand how the refrigerant flows through the system. The schematic diagram helps technicians and engineers understand the refrigeration cycle without needing to see the actual physical layout of components.
In a refrigerator schematic, each component is represented by a standard symbol. These symbols are the same worldwide, so anyone reading the diagram can understand how the system works. The diagram shows the path the refrigerant takes from the compressor, through the condenser, into the capillary tube, through the evaporator, and back to the compressor.
Every domestic refrigerator contains five main components that work together to remove heat and keep the interior cool. Understanding each component and its function is essential before drawing the schematic diagram.
1. Compressor
The compressor is the heart of the refrigeration system. It is usually located at the back or bottom of the refrigerator. The compressor sucks in low-pressure refrigerant gas from the evaporator and compresses it into high-pressure, high-temperature gas. This compression raises the refrigerant's pressure and temperature, enabling it to release heat in the condenser. In the schematic diagram, the compressor is represented as a circle with a small circle inside or as a rounded rectangle with the letter "M" inside (representing the motor).
2. Condenser
The condenser is a coil of pipe located at the back of the refrigerator. As the high-pressure, hot refrigerant gas flows through the condenser coils, it releases heat to the surrounding air and condenses into a liquid. The condenser acts as a heat exchanger, changing the refrigerant from gas to liquid while getting rid of the heat absorbed from inside the refrigerator. In schematic diagrams, the condenser is drawn as a wavy line or a zigzag line, representing a coil.
3. Capillary Tube
The capillary tube is a thin copper tube that connects the condenser to the evaporator. It acts as an expansion device that reduces the pressure of the liquid refrigerant. As the high-pressure liquid passes through the narrow capillary tube, its pressure drops suddenly, causing it to cool down significantly. This cold, low-pressure liquid then enters the evaporator. In schematic diagrams, the capillary tube is shown as a thin line or sometimes as a small rectangle labeled "capillary."
4. Evaporator
The evaporator is located inside the refrigerator cabinet, usually at the freezer section or on the back wall. The cold refrigerant liquid enters the evaporator coils and absorbs heat from the inside of the refrigerator, causing the liquid to evaporate into a gas. This absorption of heat is what makes the inside of the refrigerator cold. In schematic diagrams, the evaporator is drawn as a coil, similar to the condenser but usually labeled differently or positioned on the opposite side.
5. Thermostat
The thermostat (also called a temperature control) is the device that regulates the temperature inside the refrigerator. It senses the temperature and turns the compressor on or off to maintain the desired cooling level. When the inside temperature rises above the set point, the thermostat switches on the compressor. When the temperature drops to the desired level, the thermostat switches off the compressor. In schematic diagrams, the thermostat is shown as a symbol with contacts or as a circle with a "T" inside.
The refrigerant follows a continuous path through all components in a specific order. Understanding this sequence is crucial for drawing an accurate schematic diagram. The cycle can be summarized as follows:
- Compressor → draws in low-pressure gas and compresses it
- Condenser → releases heat and condenses gas to liquid
- Capillary tube → reduces pressure and temperature of liquid
- Evaporator → absorbs heat and evaporates liquid to gas
- Back to Compressor → cycle repeats
Follow these steps to draw a clear and accurate refrigerator schematic diagram:
Step 1: Draw the Compressor
Place the compressor symbol in the center or on one side of your paper. If using the motor symbol, draw a circle with another smaller circle inside, or draw a rounded rectangle with "M" written inside. Label it "Compressor."
Step 2: Connect the Condenser
From the outlet of the compressor (the discharge line), draw a line to the condenser. Draw the condenser as a wavy or zigzag line. Label it "Condenser." The line leaving the condenser should lead toward the capillary tube.
Step 3: Add the Capillary Tube
Draw a thin line connecting the condenser to the evaporator. This represents the capillary tube. You can label it "Capillary Tube" or simply "Capillary." Remember that the capillary tube is much thinner than the other lines in the diagram.
Step 4: Draw the Evaporator
From the capillary tube, draw the evaporator coil. The evaporator should be drawn as another coil (wavy line) but placed on the opposite side of the diagram from the condenser. Label it "Evaporator."
Step 5: Connect Back to the Compressor
Draw a line from the evaporator back to the compressor. This represents the suction line that carries low-pressure gas back to the compressor to begin the cycle again.
Step 6: Add the Thermostat
Draw the thermostat symbol between the evaporator and the compressor on the suction line. This shows that the thermostat controls when the compressor operates. Label it "Thermostat."
Step 7: Add Arrows and Labels
Add arrows along the refrigerant lines to show the direction of flow. Make sure all components are clearly labeled. Add annotations if needed to show the state of the refrigerant (such as "High Pressure" near the compressor outlet and "Low Pressure" near the evaporator inlet).
Draw a schematic diagram of a simple domestic refrigerator and label all components.
Solution:
A correct schematic diagram should show the five main components connected in the proper sequence with arrows indicating the direction of refrigerant flow. The diagram should look like a closed loop with the compressor at the center or one side, the condenser on the high-pressure side, the capillary tube connecting to the evaporator on the low-pressure side, and the thermostat controlling the compressor.
The proper order around the loop is: Compressor → Condenser → Capillary Tube → Evaporator → Thermostat → Compressor. Arrows should point from the compressor toward the condenser, through the capillary tube to the evaporator, and back through the thermostat to the compressor.
- A schematic diagram uses standard symbols to represent components
- The five main components are: compressor, condenser, capillary tube, evaporator, and thermostat
- The refrigerant flows in this order: compressor → condenser → capillary tube → evaporator → compressor
- Always include arrows to show the direction of refrigerant flow
- Label all components clearly in your diagram
- The capillary tube is the expansion device that reduces refrigerant pressure
- The thermostat controls the compressor to maintain proper temperature
| Component | Symbol |
|---|---|
| Compressor | Circle with small circle inside, or rounded rectangle with "M" |
| Condenser | Wavy line or zigzag coil |
| Capillary Tube | Thin straight line |
| Evaporator | Wavy line or coil (often labeled) |
| Thermostat | Symbol with contacts or circle with "T" |
When drawing refrigerator schematic diagrams, always start with the compressor as it is the central component. Use a ruler for straight lines and maintain consistent spacing between components. Make sure the capillary tube line is noticeably thinner than the other connection lines to accurately represent its smaller diameter. Double-check that arrows indicate the correct direction of flow—remember that the refrigerant enters the compressor as a low-pressure gas and leaves as a high-pressure gas.
In Tanzania, a refrigerator schematic diagram is used by technicians when repairing faulty refrigerators in homes, shops, and restaurants. For example, if a mama lishe's refrigerator at a market stall in Dar es Salaam stops cooling, a technician will read the schematic diagram to identify which component (like the compressor or evaporator) is failing, replace the faulty part, and get the refrigerator working again so food and drinks stay fresh. Understanding these diagrams also helps local technicians start small repair businesses, earning income while serving their community.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Make design diagram
- Make schematic diagram
- Select materials, tools and equipment
Tathmini ya matokeo
Designed and drawn refrigerator schematic diagram confirms to technical specifications Specifications and aesthetic appearance
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to: Design and make schematic drawing of the refrigerator
Principles: The student should explain the principles of:
- Designing a refrigerator
Theories: The student should explain:
- P-h chart/diagrams
- Material science
- Refrigeration cycles
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling o working tools and equipment
- Aesthetical appearance
- Environmental impacts
Swali
What is the function of the capillary tube in a refrigerator schematic?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado