Mada za sehemu hiiDesigning and making domestic refrigeratorMada 6
An evaporator coil is a key component in a domestic refrigerator. It is a coil made from copper or aluminum tubing that absorbs heat from the inside of the refrigerator and transfers it to the refrigerant. As the refrigerant evaporates (changes from liquid to gas), it absorbs heat from the surrounding air, cooling the refrigerator's interior.
The evaporator coil is usually located inside the freezer or refrigerator compartment, often at the back wall or behind the shelves. It works together with the compressor and condenser to complete the refrigeration cycle.
Before making an evaporator coil, gather the following materials and tools:
- Copper tubing (typically 6mm or 8mm diameter)
- Tube bender
- Pipe cutter or hacksaw
- Reaming tool
- Sandpaper or wire brush
- Brazing equipment (oxy-acetylene)
- Flux and brazing alloy
- Measuring tape
- Marker pen
- Clamps
- Safety goggles and gloves
Step 1: Planning and Measurement
First, determine the required coil dimensions based on the refrigerator size. The coil should have enough surface area to absorb heat effectively. Typical evaporator coils have between 8 and 16 turns, depending on the refrigerator's cooling capacity.
Use a tape measure to measure the available space inside the refrigerator cabinet. Mark the tubing at regular intervals for bending.
Step 2: Cutting the Tubing
Cut the copper tubing to the required length using a pipe cutter. Leave extra length for connections (about 30-50 cm extra). After cutting, use a reaming tool to remove burrs from the inside of the tube. Clean the ends with sandpaper or a wire brush to ensure good brazing.
Step 3: Bending the Coil
Use a tube bender to create uniform bends. The coil is typically bent into a serpentine (zigzag) pattern. Maintain consistent spacing between bends (usually 5-8 cm). Bend gradually to avoid kinking the tubing, which would restrict refrigerant flow.
Step 4: Installing Mounting Supports
Attach mounting brackets or clips to secure the coil in place. These can be made from sheet metal and attached using rivets or screws. Ensure the coil is positioned to allow air to circulate freely around all sides.
Step 5: Connecting the Tubing
Connect the evaporator coil to the refrigerant lines using proper fittings. Apply flux to the joint areas before brazing. Use oxy-acetylene equipment to heat the joint evenly and apply brazing alloy. Allow the joint to cool naturally.
Step 6: Testing for Leaks
After brazing, test all joints for leaks using a leak detector or soap bubble method. Connect the manifold gauge to check system pressure. A properly made coil should hold pressure for at least 30 minutes without significant loss.
Step 7: Evacuation and Charging
Use a vacuum pump to remove air and moisture from the coil and system. Evacuate to below 500 microns. Then charge the system with the correct amount of refrigerant as specified by the manufacturer.
A domestic refrigerator requires an evaporator coil with 12 turns. The available space is 40 cm wide and 50 cm tall. The tubing diameter is 6 mm.
Calculating tubing length:
- Height per turn (including spacing): 50 cm ÷ 12 = approximately 4.2 cm
- Width of coil (including bends): 40 cm
- Straight sections per turn: 2 × 40 cm = 80 cm
- For 12 turns: 80 cm × 12 = 960 cm = 9.6 m
- Add extra length for connections: 9.6 m + 0.4 m = 10 m
Therefore, cut approximately 10 meters of 6 mm copper tubing to make this evaporator coil.
- Always wear safety goggles and heat-resistant gloves when brazing
- Work in a well-ventilated area to avoid fume inhalation
- Secure tubing with clamps during bending to prevent slipping
- Keep a fire extinguisher nearby when using oxy-acetylene equipment
- Check all gas connections before lighting the brazing torch
| Defect | Cause | Prevention |
|---|---|---|
| Kinks in tubing | Bending too sharply | Use proper tube bender, bend gradually |
| Leaky joints | Insufficient heating or flux | Clean surfaces thoroughly, apply flux evenly |
| Restricted flow | Debris inside tube | Ream ends after cutting, blow out before assembly |
| Poor cooling | Insufficient coil surface | Follow manufacturer specifications for coil size |
In Tanzania, refrigerators are essential for preserving food in households and small businesses like dukas and restaurants. A technician who knows how to make and repair evaporator coils can maintain or restore refrigerators that have stopped cooling properly. For example, if a refrigerator at a local market in Dodoma fails to cool, a technician can fabricate a new evaporator coil using copper tubing and brazing equipment, saving the business owner the cost of buying a new refrigerator — which could cost around TZS 800,000 to TZS 1,500,000 for a decent domestic model.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Make evaporator sketch
- Select materials, tools and equipment
- Pipe the evaporator coil
- Perform spray painting
- Apply safety measures
- Clean workplace tools and equipment
- Store tools and equipment
- Commission the system performance
Tathmini ya matokeo
Designed refrigerator as per to technical Specifications and aesthetic appearance
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to: Make evaporator coil
- Apply safety precautions
- Detect refrigerant leakage
Principles: The student should explain the principles of:
- Designing a Evaporator coil
Theories: The student should explain:
- P-h chart/diagrams
- Material science
- Refrigeration cycles
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling of working tools and equipment
- Aesthetical appearance
- Environmental impacts
Swali
What material is most commonly used for making an evaporator coil in a domestic refrigerator?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado