Mada za sehemu hiiDesigning and making domestic refrigeratorMada 6
Charging and Commissioning a Refrigeration System
Charging and commissioning are the final and critical steps in assembling a domestic refrigerator. Charging means adding the correct amount of refrigerant into the closed refrigeration system, while commissioning means testing and adjusting the system to ensure it operates efficiently, safely, and according to design specifications. Without proper charging and commissioning, even a well-built refrigerator will not cool properly.
When a refrigeration system is first built or serviced, it contains air and moisture inside the pipes. Before adding refrigerant, you must remove these contaminants using a vacuum pump. The refrigerant is the working fluid that absorbs heat from the cabinet and releases it outside through the condenser.
The correct charge is vital because:
- Too little refrigerant reduces cooling capacity
- Too much refrigerant increases pressure, reduces efficiency, and can damage the compressor
- The charge must match the system's design (usually indicated on the manufacturer's label)
Step 1: Evacuation (Vacuuming)
Before charging, the system must be evacuated to remove air and moisture:
- Connect the manifold gauge blue (low-pressure) hose to the suction service port on the compressor
- Connect the red (high-pressure) hose to the discharge service port
- Connect the yellow hose to the vacuum pump
- Open both manifold valves and run the vacuum pump for at least 15–30 minutes
- Close the valves and check that the gauge reads below 500 microns (or close to -30 inHg)
- If the vacuum holds, the system is leak-free and ready for charging
Step 2: Charging the Refrigerant
- Connect the refrigerant cylinder (e.g., R-134a or R-600a) to the yellow hose
- Weigh the refrigerant cylinder before charging and record the weight
- Open the valve slightly and allow refrigerant to enter the system while the compressor is running
- Monitor the low-pressure gauge — it should read between 0.5–1.5 bar (7–22 psi) for a domestic refrigerator
- Add refrigerant slowly until the system reaches the correct pressure and the cabinet begins to cool
- Weigh the cylinder again and calculate the amount added (compare with the manufacturer's specified charge)
After charging, commission the system by checking its performance:
- Check temperatures — Measure the evaporator (freezer) temperature with a thermometer; it should reach -18°C or lower
- Check condenser — It should feel warm to touch, indicating heat rejection
- Check for leaks — Use a leak detector (electronic or soap solution) around all joints and connections
- Check compressor current — Use a clamp-on meter; the running current should match the nameplate value (typically 1–2 A for small domestic units)
- Check superheat — Measure suction line temperature at the compressor inlet; superheat should be 5–10°C above the evaporator saturation temperature
- Check subcooling — Measure liquid line temperature; subcooling should be 3–8°C below the condenser saturation temperature
- Run the refrigerator — Let it run for at least 30 minutes and verify consistent cooling in all compartments
- Always wear safety goggles and gloves when handling refrigerant
- Never charge a system while it is under vacuum — always run the compressor during charging
- Ensure good ventilation when working with refrigerants
- Keep ignition sources away from the work area (some refrigerants are flammable)
- Use proper clamps to secure hoses and connections
| Tool | Purpose |
|---|---|
| Manifold gauge set | Measure high and low pressures |
| Vacuum pump | Remove air and moisture from system |
| Refrigerant cylinder | Supply the correct refrigerant |
| Leak detector | Find refrigerant leaks |
| Clamp-on meter | Measure compressor current |
| Thermometer | Measure temperature of cabinet and components |
| Multimeter | Check electrical connections |
A domestic refrigerator requires 60 grams of R-134a refrigerant. During charging:
- Cylinder weight before charging: 4,200 g
- Cylinder weight after charging: 4,138 g
- Amount added = 4,200 - 4,138 = 62 g
The technician added 62 g, which is slightly above the specified 60 g. The system should be checked to ensure performance is not affected. If the low-pressure reading is too high, some refrigerant may need to be recovered.
In Tanzania, charging and commissioning skills are essential for refrigeration technicians working in small repair shops in cities like Dar es Salaam, Arusha, and Mwanza. When a customer's domestic refrigerator stops cooling, the technician must evacuate the system, add the correct refrigerant charge (often R-134a or R-600a), and commission the system to restore proper cooling. This service typically costs between TSh 50,000 and TSh 150,000 depending on the problem, making this skill both valuable for employment and important for helping households preserve food and medicine.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select materials, tools and equipment
- Evaluate and charge with refrigerant
- Apply safety measures
- Clean workplace tools and equipment
- Store tools and equipment
- Commission the system performance
Tathmini ya matokeo
Designed refrigerator as per technical Specifications and aesthetic appearance
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Detect refrigerant leakage and commission
Principles: The student should explain the principles of:
- Refrigeration cycle
- Designing a refrigerator
- Heat transfer
Theories: The student should explain:
- System components capacity
- Material science
- Refrigeration cycles
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling of working tools and equipment
- Aesthetical appearance
- Environmental impacts
Swali
What is the main purpose of evacuating a refrigeration system before charging it with refrigerant?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado